Smellyhobbit said:

Here’s my first culture I’m happy enough with to post. The credit for this plate goes to all you wonderful people here. Special thanks to Rotnpins, Guerrilla, and Rumfor.

---

Smellyhobbit said:

Here’s my first culture I’m happy enough with to post. The credit for this plate goes to all you wonderful people here. Special thanks to Rotnpins, Guerrilla, and Rumfor.

---

Yea, that looks rad...

Smellyhobbit said:

Here’s my first culture I’m happy enough with to post. The credit for this plate goes to all you wonderful people here. Special thanks to Rotnpins, Guerrilla, and Rumfor.

---

Smellyhobbit said:

Here’s my first culture I’m happy enough with to post. The credit for this plate goes to all you wonderful people here. Special thanks to Rotnpins, Guerrilla, and Rumfor.

---

beautiful just beautiful


Also with the charcoal in plates really funky thick ropes and bad transfer but without charcoal game changer!

nektar61 said:

Bismillah said:

My first plins



This fluffy plate produced some

---

Beautiful plins. Clone them.

---

I cloned a few of them until I ran out of plates.

I tried to cut with a scalpel, but managed to mangle one in the process.
After transfer and two days later:


I saw no other way than to pick the smaller plins. I guess this will transfer some of the surrounding mycelium, which means I won't get a single strain.
After transfer and two days later:


I put the source plates for these in the fridge since I'm not quite ready for a2g yet. Is that a good idea, or should I just continue to collect pins? I also have some agar slants, but I guess the plates can be stored in the fridge for a while.

I left the fluffy plate out, and the plins keep growing:

shroomsurf said:

Here's a better pic of my first best T1...

---

Smellyhobbit said:

shroomsurf said:

Here's a better pic of my first best T1...

---

Wow that’s some really nice, even growth, especially for a T1

---

Thanks, they all came from MSS, all three look like that basically and I guess I'm going to put them into my spawn bags when their fully colonized!

Did them with gloves, mask, 70% rubbing stuff, in front of my hood and used sterile scalpel...

Next steps for me:

1. Buy PC, make agar, make my own spawn bags and do 66qt tubs...
2. Get some weirdo albino strains like ghost, yeti, APE and either jack frost or pearly gates...

shroomsurf said:

Smellyhobbit said:

shroomsurf said:

Here's a better pic of my first best T1...

---

Wow that’s some really nice, even growth, especially for a T1

---

Thanks, they all came from MSS, all three look like that basically and I guess I'm going to put them into my spawn bags when their fully colonized!

Did them with gloves, mask, 70% rubbing stuff, in front of my hood and used sterile scalpel...

Next steps for me:

1. Buy PC, make agar, make my own spawn bags and do 66qt tubs...
2. Get some weirdo albino strains like ghost, yeti, APE and either jack frost or pearly gates...

---

Rusty2096 said:

shroomsurf said:

Smellyhobbit said:

shroomsurf said:

Here's a better pic of my first best T1...

---

Wow that’s some really nice, even growth, especially for a T1

---

Thanks, they all came from MSS, all three look like that basically and I guess I'm going to put them into my spawn bags when their fully colonized!

Did them with gloves, mask, 70% rubbing stuff, in front of my hood and used sterile scalpel...

Next steps for me:

1. Buy PC, make agar, make my own spawn bags and do 66qt tubs...
2. Get some weirdo albino strains like ghost, yeti, APE and either jack frost or pearly gates...

---

Maybe it's just from the picture and food colorant but :

why is the transfered piece clearly while but the rest of the growth gray?

Is it only me but despite being symmetrical it looks disorganized?

If I were you, I would go for T2 (and not go to grain) and ask for an experienced cult to look at it.

Edit: how long as it been between the transfer and the picture?

---

Hi and thank you for your very direct response! It's been about 10 days or less and yes they don't look perfect but I do think I used a blue plate to transfer from!?

I might go T2, I guess I was not so picky and wanted to keep the ball rolling...

I may have put the myc side up not down on these T1's, which is why they look white!?

It's B+ and I don't know how it should look and would have 4 to choose from to do T2's which I could post if you wanna see the rest?

Rusty2096 said:

shroomsurf said:

Smellyhobbit said:

shroomsurf said:

Here's a better pic of my first best T1...

---

Wow that’s some really nice, even growth, especially for a T1

---

Thanks, they all came from MSS, all three look like that basically and I guess I'm going to put them into my spawn bags when their fully colonized!

Did them with gloves, mask, 70% rubbing stuff, in front of my hood and used sterile scalpel...

Next steps for me:

1. Buy PC, make agar, make my own spawn bags and do 66qt tubs...
2. Get some weirdo albino strains like ghost, yeti, APE and either jack frost or pearly gates...

---

Maybe it's just from the picture and food colorant but :

why is the transfered piece clearly while but the rest of the growth gray?

Is it only me but despite being symmetrical it looks disorganized?

If I were you, I would go for T2 (and not go to grain) and ask for an experienced cult to look at it.

Edit: how long as it been between the transfer and the picture?

---

I was thinking the same thing about the color and disorganization, but I wasn't sure so I didn't say anything... but that whole group of plates you posted has a funny look to them.. maybe a TC can take a look at the pictures for you