Fiet said:

DV8DUG said:

Fiet said:

DV8DUG said:

Those look fine. Except for that horned ant head in the middle of the right side jar.

Quit trippin' on grains drying out and inoculate already.

---

I do inoculate from my LC 3-4cc I do no shake after inoculation is that what you recommend? so i see some wet Grains on the bottom from the LC you know what i mean a area around the jar

---

OK. I shake after I inoculate. Then LITFA for a week or two. Moisture DOES NOT cause bacteria. It just spreads it quicker.

---

Hey, but i can let them grow without shaking after the inoculation?? I like too see the growth then later do the only one first shake. I hope i kill all bacteria after 2h at 15psi.

Then i have another question:

I bought a Gelatine Kapuls Mashine for my later Mushroom i will powder
Kapsul Mashine 00

I bought the Typ ore Size 00 I hope the Typ 00 is a good choice and not too Big??

---

bodhisatta said:

use second flush or third flush ones for larger prints.

---

tomtacy said:

Do Pan Cyans get bigger caps and better prints in later flushes?

bodhisatta said:

use second flush or third flush ones for larger prints.

---

https://www.shroomery.org/forums/showflat.php/Number/24461957

---

Kloakk said:

tomtacy said:

Do Pan Cyans get bigger caps and better prints in later flushes?

bodhisatta said:

use second flush or third flush ones for larger prints.

---

https://www.shroomery.org/forums/showflat.php/Number/24461957

---

Depends, I would take some prints from first flush just to be sure, but if you get a decent second flush the fruits tends to be bigger yes.

---

Thanks for a quick response!
First flush is already sporulating, fruits look decent and I will take these prints following your advice tomorrow

tomtacy said:

Thanks for a quick response!
First flush is already sporulating, fruits look decent and I will take these prints following your advice tomorrow

---

Better safe then sorry right? One can't have too many prints anyway, there's always an option to give them away at the marketplace, oh and nice fruits

Kloakk said:

tomtacy said:

Thanks for a quick response!
First flush is already sporulating, fruits look decent and I will take these prints following your advice tomorrow

---

Better safe then sorry right? One can't have too many prints anyway, there's always an option to give them away at the marketplace, oh and nice fruits

---

Sure it is! Can't wait to be ready for the marketplace, already have a better (mail dependent) collection of Pan's prints to work with than I could imagine.
Hopefully I will get this art to the point of sharing spores back to the community.

Hell yes I got a Snoop Dogg gif response!

Quote:

I break and shake once when I send to bulk because it works with my workflow.

I use 00 capsules as well.

---

Reishi Uchiha said:

Is this sweating too much? Temp swings from 67 to 76 sometimes.
And the grain was a bit wet, it had very little condensation pre noc.
I couldn't find any reference on threads that show clean spawn so if some experienced eye could tell, please do. I'm guessing I could send them to bulk with this colonization, just don't wanna waste it if this is bad.

---

when my Jars get fully colonized they start compensating at the top. Even with the room staying at 74-76f. I think its just from metabolic things. As long as its not down in the grains you should be good to go.

I'd send it dude.


Here are some of my jars fully colonized with condensation in them

Fiet said:

My both shoebox 3l after 2 days. I place them near my heater between my bedroom temps I check 21-23 Celsius. The condensation is not a problem? The lid is close and i don't have too do a Air exchange just let it allone right? My fear is mold from not too much air.

---

DV8DUG said:

Fiet said:

My both shoebox 3l after 2 days. I place them near my heater between my bedroom temps I check 21-23 Celsius. The condensation is not a problem? The lid is close and i don't have too do a Air exchange just let it allone right? My fear is mold from not too much air.

---

Be careful when heating like that.The ideal way is to heat a small area. When you heat like that it is really inconsistent. If your shoe boxes have small plastic gussets on the lid groove to hold the lid just off box. So your sweaty shoes can dry out. That's your FAE.

---