ReverendMyc said:

Anomalocaris said:

I decided to recase it. I added a very thin casing layer ( all the pasteurised casing I had left)



Im using ez dial monotub with a few extra holes. I opened up a couple extra holes now. I also have a fan in the room not pointing at the tub running on low for 3 minutes every hour just to have some more fae.

You think its gonna be enough? I can also increase how long the fan stays on but im worried it will dry the tub

---

Just to add some data points. I grow them in tubs with more holes. Takes some dialing in for your setting but it can be done without foggers and fans. Maybe not as well as a dreamer, tent or other more complex set ups, but doable.

***********************************************


Pan Cyan Bunnell
trays 1988 1989 from jars 1936 1937 2nd gen clone
1pt spawn 3pt compressed hpoo/coir 1/2 pt top layer
Spawned 2024-06-14.
Filter stickers on inside of all holes except 2 top center short side at spawn.

Day 3


Day 4

Cased

Day 6

Pins!

Day 7


Day 11

Small caps on an even pin set, if a bit sparse. Opened a couple of low middle holes on the long sides in hopes of improving the cap size for prints. Likely too late to help with this flush. They also did not get any misting for the last three days due to traveling.

Day 13

Harvest 1. Small caps.

Day 19

Harvest 2 with larger caps for printing.

Day 20

Heading for flush three.

Day 25

One tray got the green. I left the house at 80f for several days which didn't help. I think the unusual expression was caused by the contam but was interesting enough for a bunch of pictures. Composted the green tray and will keep an eye on the other.

Day 28

Flush 4 inbound.

Day 30

When I returned they looked ready to print so I obliged them.

Dark after 12 hours so started another round.



*********************************

Pan Cambo Komodo
trays 1990 1991 from jars 1940 1941 2nd gen clone
1pt spawn 3pt compressed hpoo/coir 1/2 pt top layer
Spawned 2024-06-14.
Filter stickers on inside of all holes except 2 top center short side at spawn

Day 3


Day 4

Cased

Day 6

Pins!

Day 7


Day 11

Liking this pin set. Would be happier with larger caps. Opened middle low holes on the long sides. No misting for the last three days due to travel. Also wondering about the exploding stipes.

Day 13

1st flush harvest.

Day 19

2nd flush harvest with better caps for printing.


Day 20

Heading for 3rd.

Day 25

Left the house thermostat on 80f while traveling and came back to some stressed fruits. Harvested, misted and sent back to work.

---

chewinggum said:

Mackload said:

chewinggum said:

I recently got a sample of these free from a provider. I came here asking the basics first:

1) Does the substrate have to contain manure?
2) If yes, how much?
3) Is everything else the same in terms of cultivation (inoculation, transfer to monotub, etc)?

---

link

---

Much appreciated!

I made this small jar (PF tek style) a month ago which is basically a typical CV substrate but with around 10-20% manure (store bought dried manure bovine bellets).



The mycelium is taking its time to grow, it's been over a month and this is the progress it's made, although it still grows day by day. Any ideas on what to do? Shall I just continue being patient?

---

Anyone?

PuffM4gicDr4gon said:

It's probably not a good sign if it's taking that long.

I haven't done Pans in PF Tek yet, but grains colonize in 5-15 days. I would imagine a healthy PF Tek running Pans would be close to the same amount of time.

---