Proposition 122 said:

tholos said:

Proposition 122 said:

Best way to clean a Media Bottle of left over agar?

---

Microwave it to melt it, pour it into the sink with your cold water running. Use a brush if you can to scrub inside the bottle

---

Media Bottle won't fit in my microwave :-(
Won't cold water help solidify the agar and maybe plug the drain?

---

Proposition 122 said:

tholos said:

Proposition 122 said:

Best way to clean a Media Bottle of left over agar?

---

Microwave it to melt it, pour it into the sink with your cold water running. Use a brush if you can to scrub inside the bottle

---

Media Bottle won't fit in my microwave :-(
Won't cold water help solidify the agar and maybe plug the drain?

---

Proposition 122 said:

Best way to clean a Media Bottle of left over agar?

---

Mr Piggy said:

Proposition 122 said:

tholos said:

Proposition 122 said:

Best way to clean a Media Bottle of left over agar?

---

Microwave it to melt it, pour it into the sink with your cold water running. Use a brush if you can to scrub inside the bottle

---

Media Bottle won't fit in my microwave :-(
Won't cold water help solidify the agar and maybe plug the drain?

---

I pour leftovers in the trash for this reason.

Place it in a pot of boiling water with the neck sticking out and the lid off.

---

LadysKnight said:

yoosername said:

LadysKnight said:

I need to fit 100mm, those seem illusive.

---

Fisher Scientific makes a sterilizer box that would work, they are high quality but cost prohibitive.  Sometimes you can find them on eBay.

---

You're giving me ideas...

---

GenesisCorrupted said:

callmehippie said:

I picked up one of these sterilizing canisters



a while back and it's just been sitting around. I'm ready to use it though.

I know there's a few people out there I recall that have mentioned they have one.

Just curious if anybody that uses one of thes could  hook me up with any tips and tricks they might have figured out when using one.  so I don't have to do as much trial and error.

If you have one of these do you have some sort of method that you have figured out to make the best plates when using it?

Or is it just as easy as load it up and sterilize it and that's it?

---

The best part is there really isn't any tips or tricks.
It's very straightforward. Loaded up as full as it can go. Load it into your PC  as  flat as possible.
There should be little holes that lineup with the inside and outside when you put the cap on.

---

GenesisCorrupted said:

Have you ever mixed two parts pineapple juice with one part Malibu rum?

---

yoosername said:

LadysKnight said:

I need to fit 100mm, those seem illusive.

---

Fisher Scientific makes a sterilizer box that would work, they are high quality but cost prohibitive.  Sometimes you can find them on eBay.

---

callmehippie said:

LadysKnight said:

I need to fit 100mm, those seem illusive.

---

The one that I posted that I have is for 100 mm. I cannot remember where I got it from though. I thought it was Amazon but it doesn't appear so. I'll keep looking around if I can find a link I'll post it for you.

---

Cheapest I found so far. Ebay



https://www.ebay.com/itm/385833869298?


Here's one. 



Stainless Steel Autoclave Rack https://a.co/d/9RXHBge

100mm canister.  But it's fucking expensive. I do not think I paid this much. I'll keep looking for you.


And then this is just a rack. Without the canister. You could probably wrap it in foil Maybe but it's cheaper and definitely usable.



Stainless Steel Petri Dish Carrier Rack for 100 mm Glass Petri Dish, 10 Dishes, Autoclave Safe https://a.co/d/g17J7he

AZ Starman2112 said:

Ok Fam, I have this 16 qt tub of Hillbilly I sent the grain to bulk in on June 16th. The grain was healthy and smelled beautiful. It is now July 24 and I have no pins, but I have myc. There’s no contamination and the tub smells healthy like fresh shroomies. Today although the conditions in the tub were great, I was concerned the sub may have been a bit dry, so I injected it with 80cc of water, 10cc in 8 different spots. I took these pics after I injected the sub, so any yellow you see like the top right corner is some of the water that seeped up from the sub. Any idea on how long Hillbilly takes? Or what can I do to get this to fruit?

---

if it were mine i would mist it and keep it glistening with the tiniest beads, let them evaporate and mist again..
inject water? im not sure that was necessary. it is nicely coming along.
leaving it in peace now can be tricky but worth it

chris77 said:

AZ Starman2112 said:

Ok Fam, I have this 16 qt tub of Hillbilly I sent the grain to bulk in on June 16th. The grain was healthy and smelled beautiful. It is now July 24 and I have no pins, but I have myc. There’s no contamination and the tub smells healthy like fresh shroomies. Today although the conditions in the tub were great, I was concerned the sub may have been a bit dry, so I injected it with 80cc of water, 10cc in 8 different spots. I took these pics after I injected the sub, so any yellow you see like the top right corner is some of the water that seeped up from the sub. Any idea on how long Hillbilly takes? Or what can I do to get this to fruit?

---

if it were mine i would mist it and keep it glistening with the tiniest beads, let them evaporate and mist again..
inject water? im not sure that was necessary. it is nicely coming along.
leaving it in peace now can be tricky but worth it

---