I'll do my best to respond to everything you mentioned.
13eetleJuice said: Ok, either you are or you aren't a first time grower. How can you be a semi-first timer? There is only one first time. There's absolutely nothing wrong with it and you will be welcomed here no matter how much or little mycological experience you have under your belt.
I used the term "semi-first time grower" as I had attempted to grow once before but got zero mycellium growth and tons of contamination. This is simply the first time I've actually grown a mycellium patch; that's all I was trying to convey.
13eetleJuice said: You also mention that you are using an unknown sporeprint. I can only offer you my words of caution here. Be careful with things you do not understand or know the origin of.
The spore print is unknown and therefore it is not to be grown for consumption. This is an experiment in growing mycellium; the cakes are to be discarded once full colonization is done. A waste, perhaps, but "when in doubt, throw it out".
13eetleJuice said:
MrBoboFace said: I followed the technique fairly closely, using BRF, perlite, and distilled water for the substrate.
Perlite is superheated volcanic glass and is used to regulate humidity in your fruiting chamber. It is not a suitable substrate. I assume you actually used vermiculite, but have gotten the terminology confused. Don't worry, as this is a common mistake of those new to mycology. If you did however use perlite and got results I can only say that I've never been introduced to this method. I'm sure it's possible but it's not really a decent substitute for vermiculite at all.
I am not confused in the terminology. I did indeed use perlite for my substrate, not vermiculite (chipped mica). The perlite has done well so far. I know that perlite is used primarily to regulate humidity within a fruiting chamber, but I purchased the perlite as a substitute for the vermiculite that was needed to act as filler for the substrate. There has been substantial condensation on some of the jar walls, however, which may be a side effect of using perlite instead of the water-absorbing vermiculite. Vermiculite may encourage faster growth, however. I will need to test this.
13eetleJuice said: I suggest you make a separate graph for each jar and be sure that it is clearly labeled. I'm having a hard time making heads or tails of that graph.
And here we go:
 1. Day 1 was inoculation day. Mycelium didn't appear until Day 7. 2. On Day 7 the jars were moved from underneath my bed to the warm computer, and an insulating blanket was placed over them. You can see the general growth rate. 3. On Day 9 I was concerned that the substrate was getting too warm (31C) and I removed the blanket. 4. On Day 13 I put the blanket back on. 5. On Day 23 I removed the blanket again, for fear that the mycelium had been kept too warm (86F - I was overly cautious).
13eetleJuice said: You will have MUCH less halts in the growth if the temperature is kept in a CONSTANT and OPTIMAL range of 84-86F. Mycelium hates changes in temperature (or anything for that matter). Consistency is the key.
I see. So you are saying that halted growth is not normal, then. Perhaps my next experiment should involve two batches: one with fluctuating temperatures, and another in a Tub-in-Tub setup with a constant temperature. Thanks for the tip!
13eetleJuice said:
MrBoboFace said:
Use a pressure cooker, even a cheap one. Just boiling the jars isn't enough.
Boiling is actually quite sufficient when using BRF/Verm as a substrate. A PC is not needed if proper sanitary conditions are met throughout.
Not in my past experience. Many newbie growers, such as myself, have not developed the necessary methods to maintain sanitary conditions. I make the suggestion of using a pressure cooker as it will assist the new grower in avoiding contamination. My first time using a pressure cooker resulted in zero contamination, while a previous attempt without a PC resulted in total bacterial contamination. I maintain my statement that a pressure cooker is very helpful in reducing or eliminating contamination potential, even with the relatively clean BRF/vermiculite mix.
13eetleJuice said: Many of the questions you seek to answer through experimentation have already been answered multiple times by those with decades of experience in mycology. Good luck to you and may this be a fruitful hobby for you.
Oh, I realize that most of what I'm mentioning here is already covered in the FAQ and that my "experimental methods" are likewise fully tested and proven/disproven within the FAQ, by people with far more experience than me. However, all of these suggestions/warnings/methods should be able to be replicated by another grower. I'm testing the theorem. If I can prove a known fact, then I feel more confident in proving/disproving an unknown method.
|