bluespirit13 said:

Been keeping them around 68 - pretty concerned to only have this one mushroom still :/

Open to any suggestions on encouraging some
More pins. Heat is back on now!

---

Pin said:

Pretty happy with this so far, but what's up with the split stipes?
These are rusty whites. Thanks!

flash/no-flash

---

Might just be the pics but the sub looks little dry

LewDoja said:

Pin said:

Pretty happy with this so far, but what's up with the split stipes?
These are rusty whites. Thanks!

flash/no-flash

---

Might just be the pics but the sub looks little dry

---

LewDoja said:

Yea the surface looks a little matted (from misting).

After harvest use a scalpel to cut X in the liner (or remove carefully)
Im Not a fan of dark liners. If I use one it's as clear as possible.

---

LilSassy said:

What should be my checklist for preventing trich during S2B? I just lost four shoeboxes to it even though I was certain that my colonized grains were fully done and clean. I had a 1:1 maybe 1:2 ratio of spawn grain to coco bliss pasteurized coco coir (so shouldn't have had any kind of pet shop style trich added and this is the same kind used in several TEK guides here)

The only thing I can think of is that maybe it was overhydrated, though I did think it was perfectly at field capacity. The boxes themselves looked to be quite humid with moisture along the sides and top pooling that would drop if I touched the lid. I also made to sanitize the room entirely before I even started work with Lysol and 70% alcohol spray (now I'm reading this isn't really necessary)

---

bluespirit13 said:

Been keeping them around 68 - pretty concerned to only have this one mushroom still :/

Open to any suggestions on encouraging some
More pins. Heat is back on now!

---

It's odd to only have 1 in first flush. The second might be better.

I always run unmodified 6qt sterilites. both the white lid and the grey lid type. I just leave them on a shelf, not inside any modded monos.

Just like this.

As long as you got your field capacity down when you spawned you should be good. There's a bunch of primordia in there so it's odd that you only have one shroom IMHO.

I personally would let it ride until that one is ready to print and clone.

LilSassy said:

What should be my checklist for preventing trich during S2B? I just lost four shoeboxes to it even though I was certain that my colonized grains were fully done and clean. I had a 1:1 maybe 1:2 ratio of spawn grain to coco bliss pasteurized coco coir (so shouldn't have had any kind of pet shop style trich added and this is the same kind used in several TEK guides here)

The only thing I can think of is that maybe it was overhydrated, though I did think it was perfectly at field capacity. The boxes themselves looked to be quite humid with moisture along the sides and top pooling that would drop if I touched the lid. I also made to sanitize the room entirely before I even started work with Lysol and 70% alcohol spray (now I'm reading this isn't really necessary)

---

Fungify said:

Hello,

I most probably have a mix spawn + sub too wet, due to the spawn. The specie is Pan Cyan. The mix is roughly 50% spawn, 50% subs (~2/3 hpoo + 1/3 "hay").
The operation was done 9 days ago, absolutely no visible change.

Can I put it somewhere dryier/hotter to paliate this issue or am I doomed ?

---

I reupload my question since it was lost in the abyssal flow of messages, plus I add some stupid emoji to attract attention :

LewDoja said:

To be able to spot contamination in a place that is perfect environment (stagnant, moist) to harbor them.

Side pins are notorious from Maz but other should be able to be avoided by packing the shit out of the sub during spawning.

My coir is probably just barely under FC (squeeze the F#@! outta it)
I save a little bit of spawn to throw on top of surface. Pack really well especially the sides. Level... top layer is not as compacted... level... and spray this top layer till it's soaked but not pooling.

---