Home | Community | Message Board


This site includes paid links. Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Jump to first unread post Pages: 1
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
Keeping down the top TiT tub?
    #7768645 -

A friend of mine just set up his TiT, but the top tub will only float on the water below, even with a few bricks in it. How should he keep the top tub down?

I tried searching the forum for him, but nothing came up.


--------------------
tripping eyes and flooded lungs
northern downpour sends its love

Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Querjek]
    #7768653 -

Try using 4 Zip Ties.... one on each corner.


--------------------
You cannot yet touch my daughters awesome boobage
:jiggly:
You must fight to the death in the Breastriary of Nippopolis.




I thought Gene Wilder was cool BEFORE he was dead.

Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Querjek]
    #7768657 -

you can drill some holes and use zip ties to hold the top container down...
at least that is what some people do.


I prefer using this type of a TIT setup...

Roadkill said:
I use 2 different size Rubbermaid's.
The smaller one goes inside the bigger one...so you won't crush the submersible aquarium heater.


Put the submersible aquarium heater in the larger (bottom) Rubbermaid or container.
add your water.


Then put the smaller Rubbermaid or container into the larger one.


Play with the temp setting on the submersible aquarium heater, in the bottom container...until you dial the heat in to 81 degrees F. inside the top container.
Then put your jars inside the top container...and shut the lid on the top.
Set it and forget it...lol







with this TIT setup there is a 4" to 5" clearance between the 2 tubs...

so you don't have to worry about the top one floating.



tc


--------------------
Laterz, Road

Who the hell you callin crazy?
You wouldn't know what crazy was if Charles Manson was eating froot loops on your front porch!


Brainiac said:
PM the names with on there names, that means they have mushrooms for sale.


Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Funkatron9000]
    #7768669 -

i done zip ties to, but first i put 4 coffee mugs on the bottom to keep top tub good distance away from fish heater but that was because my top tub was a bit smaller

Edited by smokedout420 (12/17/07 11:35 AM)

Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Querjek]
    #7768897 -

When I used a TiT, I also found it trick to get the top tub down, but before I finally got it weighted down I would just let it float, and the internal temp of the top tub still rose to desired levels.
However it did fluctuate way more than the submerged top tub.

Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Green420Thang]
    #7769199 -

My tit floats on the water and it stays between 80F an 82F. Havent had a problem yet.

Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Querjek]
    #7769297 -

we need more TIT's in this thread....



:grin:


--------------------
Laterz, Road

Who the hell you callin crazy?
You wouldn't know what crazy was if Charles Manson was eating froot loops on your front porch!


Brainiac said:
PM the names with on there names, that means they have mushrooms for sale.


Extras: Filter Print Post Top
Re: Keeping down the top TiT tub? [Re: Roadkill]
    #7769436 -

i used planks of wood. 6" wide by about 1/2 thick. I cut about 2 8" lengths and then screwed into them through the bottom and top tub (with washers)

e.g.


--------------------
Rye -- WBS | Grain LC -- G2G | Bulk -- Monotub | 50/50 -- Late Casing -- A Pinning Strategy
Disclaimer: My opinion is subject to change at short notice subject to but not limited by new information and knowledge being made available.

Extras: Filter Print Post Top
Jump to top Pages: 1


Similar ThreadsPosterViewsRepliesLast post
* down side to big rubbermaid tubs? Chills420 version2 5,023 16 01/31/03 01:59 PM
by SixTango
* tips on making rubbermaid containers air tight? venora 11,146 15 07/10/02 04:24 PM
by invader
* Any advice on keeping my cakes moist? Juki 849 5 07/05/02 12:12 PM
by Shaw
* Rubbermaid Growing Chamber... drunkgoat 2,389 8 08/29/01 09:32 AM
by isis
* rubbermaid Anonymous 823 7 02/07/03 11:31 AM
by BladeLSD
* 18 Gallon RubberMaid Roughneck PooGrower 1,614 3 02/19/03 04:47 AM
by Chills420 version2
* duel tub fruiting chamber construction question.
( 1 2 all )
TheGanjaGorilla 5,129 21 06/13/03 04:38 PM
by TheGanjaGorilla
* On the subject of rubbermaid Larrythescaryrex 2,173 13 10/04/02 09:07 PM
by iloveraving

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: DERRAYLD, Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, the_chosen_one, LogicaL Chaos, 13shrooms, hamloaf, cronicr, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a
1,798 topic views. 17 members, 522 guests and 172 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:

Copyright 1997-2026 Mind Media. Some rights reserved.

Generated in 0.032 seconds spending 0.01 seconds on 16 queries.