Home | Community | Message Board


World Seed Supply
Please support our sponsors.

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Amazon Shop for: ½ Pint Jars, Microscope

Jump to first unread post. Pages: 1
InvisibleCondi1
old hand
Registered: 01/01/00
Posts: 502
Re: Need Help with Spore printing!!
    #72959 - 01/26/00 02:09 AM (16 years, 10 months ago)

.

[This message has been edited by Condi1 (edited October 06, 2000).]



Post Extras: Print Post  Remind Me! Notify Moderator
Offlinen8
member
Registered: 12/14/99
Posts: 133
Last seen: 15 years, 3 months
Re: Need Help with Spore printing!!
    #72961 - 01/26/00 06:37 AM (16 years, 10 months ago)

i don't think the size matters all that much as long as you got some... a cap that's about 1/2 inch wide will be fine. i don't know about sterile card card storage, i've found that all the available info on that is a little vague also. i would just use a jar.


Post Extras: Print Post  Remind Me! Notify Moderator
InvisibleScratcher
Stranger

Registered: 01/06/00
Posts: 2,323
Loc: eH
Re: Need Help with Spore printing!!
    #72962 - 01/26/00 02:52 PM (16 years, 10 months ago)

Here's what I do: Sterilize a 1/2 pint jar with 1 small hole punched in the top and a piece of electrical tape over the hole. When the shroom starts to drop its spores (you see a bit of purple on the stem) poke a sterilized pin in the top of the cap then snip it off with a pair of sterilized scissors. Take lid off jar (clean hands, wear mask, etc.) and quickly transfer cap into jar and tighten lid. Wait until shroom drops spores. Open jar, quickly take out cap and add 2/3 cup of sterile water. Tighten the lid, shake it up, and presto chango: SPORE SOLUTION! Peel back tape and insert syringe when ready to innoculate.

------------------
Holy shit do I feel good! Where am I?



Post Extras: Print Post  Remind Me! Notify Moderator
Anonymous

Re: Need Help with Spore printing!!
    #72963 - 01/26/00 10:24 PM (16 years, 10 months ago)

You have lots of choices.

1. use a glass microscope slide, works well.
2. use filter paper (from scientific supply places)
3. use jars
4. tin foil (wiped with alcohol of H202)

Take your pick, they all work fine.



Post Extras: Print Post  Remind Me! Notify Moderator
Jump to top. Pages: 1

Amazon Shop for: ½ Pint Jars, Microscope

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Similar ThreadsPosterViewsRepliesLast post
* Spore printing question scottshrooms 543 5 07/09/03 07:34 AM
by MAIA
* Spore Prints chaserella 884 5 03/22/06 10:45 PM
by Mushit
* spore printing pacodestroys 1,016 12 06/30/03 09:39 PM
by tekramrepus
* Utilizing unsterile spore prints Acaterpillar 1,323 8 05/11/09 04:38 PM
by caphillkid
* How do you use spore prints efficently? dnkyrhubarb 5,985 10 08/21/16 01:09 PM
by kenetic
* Attention Newbies-Make Spore Prints With Foil! Catzeye 8,707 1 02/20/02 03:54 PM
by psilocybinjunkie
* THIN SPORE PRINTS geckoshroomer 374 2 01/02/03 01:36 PM
by EthnoJimmy
* Something that doesn't make sense to me about spore prints/syringe making Chrissi 2,382 18 08/30/08 04:39 PM
by Krez

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Magash, Shroomism, george castanza, Prisoner#1, RogerRabbit, Citric, total, FooMan, 13shrooms, stonesun, EvilMushroom666, cronicr, PussyFart
709 topic views. 17 members, 39 guests and 17 web crawlers are browsing this forum.
[ Toggle Favorite | Print Topic | Stats ]
Search this thread:
Gaiana.nl
Please support our sponsors.

Copyright 1997-2016 Mind Media. Some rights reserved.

Generated in 0.026 seconds spending 0.003 seconds on 13 queries.