Home | Community | Message Board


Kratom Eye
Please support our sponsors.

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Amazon Shop for: ½ Pint Jars, Autoclave

Jump to first unread post. Pages: 1
Offlinescribbles
member
Registered: 09/23/00
Posts: 73
Loc: Southeast US
Last seen: 14 years, 8 months
Re: Making Spore Prints
    #285902 - 04/05/01 02:02 AM (15 years, 7 months ago)

Just use the print, you're most likely to get contams by making the syringe...might as well use the print :P.

-scribbles
Long Days and Pleasant Nights.


--------------------
-scribbles
Long Days and Pleasant Nights.
Check out the Church of the Universe @ www.iamm.com


Post Extras: Print Post  Remind Me! Notify Moderator
Anonymous

Re: Making Spore Prints [Re: scribbles]
    #285957 - 04/05/01 02:09 AM (15 years, 7 months ago)

Here is my version if it helps..............



10 easy steps to 'Spore Vender Independence', by Pavlov's Dog

This is the way...........

You need:

1 canning jar.
1 scraping tool eg; exacto knife, butter knife, or razor blade... improvise.
1 CLEAN sporeprint.
1 6x6 peice of tin foil.
1 STERILE 10 or 12 CC syringe w/needle.
11 or 13 cc's/Ml of DISTILLED water.

Heres EXACTLY how to do it:

1 - poke 1 hole into the edge of the canning jar lid.

2 - Get your canning jar ready, squirt 11 or 13 CC's of distilled water into the jar.

3 - wrap 6x6 peice of foil OVER the TOP of the OPEN jar.

4 - place lid w/hole on top of foil, carefully ALL excess foil that is hanging out. Now screw the ring on tight, while holding the lid in place

5 - wrap up your scraping tool in tin foil completely.

6 - If your syringe has been opened and/or used, then wrap it up in foil also.

7 - Autoclave (pressure cook) the jar w/water, wrapped scraping tool and syringe (only if its used, try to get a NEW one if possible, they come sterile). Autoclave for 15 minutes at 15 PSI.

8 - After the claving, let your jar of water and spore tools cool, you now have STERILE water, and STERILE tools to work with.

9 - Now remove the RING ONLY from the jar, remove scraping tool from the foil, carefully open your sporeprint, swiftly but carefully lift canning lid (set it aside, don't let the bottom touch ANYTHING, in fact, place it face UP 'IN' the oven, if you are using an oven) and scrape desired amount of spores into jar, then close the lid, screw ring back on, and SHAKE LIKE HELL.
*I recommend a 'Glove Box' for this part, but lots of Lysol, and an oven "USUALLY" works ;), look up 'THE OVEN TEK' for more info on that.

10 - Now you are ready to withdraw your sporejuice, flame your needle, inject through the 'foil sealed hole', tilt jar and withdraw spores. It's a good idea to let them rehydrate for 6 to 12 hours, but not mandetory. The more spores you use, the better your chances against cantams, but if all is done correctly, you shouldn't really have any problem with any amount of spores... it doesn't take much.

10 easy steps to Spore Vender independence, by Pavlov's Dog ;)





Post Extras: Print Post  Remind Me! Notify Moderator
Offlinenononsense
enthusiast

Registered: 03/26/01
Posts: 319
Last seen: 14 years, 11 months
Re: Making Spore Prints
    #285967 - 04/05/01 02:34 AM (15 years, 7 months ago)

You can make the print paper sterile by spraying it with alcohol and let it dry with a cap around. Or putting it in the oven at 130 ?C for half an hour....!


_________________________________________
Don't look at me, I didn't do it!!


--------------------
_________________________________________
I support the go.to/FreeSporeRing
Email me at [email]nononsense@shroomery.org[/email


Post Extras: Print Post  Remind Me! Notify Moderator
OfflineCableface
Stranger
Registered: 04/04/01
Posts: 6
Last seen: 15 years, 5 months
Re: Making Spore Prints [Re: nononsense]
    #286421 - 04/05/01 05:46 PM (15 years, 7 months ago)

Cool! Thanks alot guys.



Post Extras: Print Post  Remind Me! Notify Moderator
Jump to top. Pages: 1

Amazon Shop for: ½ Pint Jars, Autoclave

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Similar ThreadsPosterViewsRepliesLast post
* Post deleted by users_request malibu76 1,681 6 05/21/02 11:20 AM
by luvdemshrooms
* Attention Newbies-Make Spore Prints With Foil! Catzeye 8,695 1 02/20/02 03:54 PM
by psilocybinjunkie
* Making spore prints Ascension 1,215 4 05/18/06 02:57 AM
by Tippinthru
* making spore-prints donahue 1,205 7 02/16/03 07:04 AM
by SixCee
* Making spore prints into spore syringes combs 1,457 3 06/11/07 10:53 PM
by figgusfiddus
* Re: Making Spore Prints from Contaminated Cakes LuciferX 1,001 2 06/28/00 05:31 AM
by hitterg
* Making spore print..help Psilomind 637 1 03/09/04 06:51 AM
by MESCALATO
* what's the best material for making spore prints?
( 1 2 all )
Boondock 3,201 22 07/23/05 08:46 AM
by scatmanrav

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Magash, Shroomism, george castanza, Prisoner#1, RogerRabbit, Citric, total, FooMan, 13shrooms, stonesun, EvilMushroom666, cronicr, PussyFart
781 topic views. 32 members, 101 guests and 17 web crawlers are browsing this forum.
[ Toggle Favorite | Print Topic | Stats ]
Search this thread:
RVF Garden Supply
Please support our sponsors.

Copyright 1997-2016 Mind Media. Some rights reserved.

Generated in 0.04 seconds spending 0.002 seconds on 14 queries.