Auto-SummaryThe post discusses creating a blade for liquid culture (LC) growth in a large container. The blade, made of stainless steel, is attached to a PTFE bushing in the lid and can be spun in reverse or forward to stir grains or mix substrates. The author recommends using minimal simple sugars in the agar, such as 2% malt extract, and low-sugar broths like 0.1-0.5%. They suggest using expanded grains, which are easier for mycelium to colonize. Various methods for making blades are mentioned, including using a stainless kebab skewer or magnetic stirring devices. The post also covers moisture management and injecting sterile water if needed.
I have a large container with a blade coming down from the top down, the bushing mounted in the lid. Here is a quote about it, a few paragraphs down but the rest might be relevant reading
blackout said:I was always told it was the simple sugars typically used in LCs which were contam prone (along with excess water). As mentioned the ~10-25ml agar plate will be adding sugars to your water. If sugars are the main worry then your agar could have no simple sugars, just be grain based. Some say myc grown on a agar made of the intended end substrate may do better, as its already gotten used to it, so may take it easier & faster.
In this thread Workman (of sporeworks) recommended a agar of 2% malt extract, and a broth of only 0.1-0.5% http://www.shroomery.org/forums/showflat.php/Number/4332098#4332098 So his broths are as low as 1/20th of what the agar plate is. So blending up a "regular strength" agar plate is possibly making a broth he considers ideal. I understand the point that it is not given much time like this but still reckon it could be minimised. I wonder if 0.1% agar plates would be any use.
I have done many heavy LC grows, I was aware of contam issues so would let them colonise very well. I also avoid shaking grains by growing in their fruiting trays. Expanded grains suck up LC very well and I believe this is the key to rapid colonisation, its like micro bits of myc might be getting into the core of the partially dry grains rather than just sitting on top. You make expanded grains several ways, oversoaking and drying them off in a microwave to drive moisture out. Or baking/toasting grains.
I have made several "blades", the biggest is about 6" in diameter in a 5L tub and is all stainless passing through a PTFE bushing, this was for sclerotia grows, pulverising grains to expose the inner bits as it was not going to be reopened and so not contam prone. The simplest ones are simple stainless rods which are bent into an L shape. The lower part is hammered flat and sharpened. If only mixing up agar this may not even be necessary. And the forces needed in blending agar are minimal. My blades attach directly into a drill, i.e. I tighten the rod directly in the drill chuck. With this agar method there is probably no need for a drill, it could be turned by hand, so a strong bushing is not essential.
The simplest I can think of right now which is readily available would be a stainless kebab skewer
 If you were lazy and did not want to bend and sharpen a blade it could possibly be used as is, you can see the rounded bit you hold should be able to blend up simple agar. The top end could be cut and stuck in a drill, or it could be bend over to give you a handle to turn it easily. A cork could be stuck on the end and twist it by hand, like starting a fire, rubbing it quickly between your palms. The bushing could be a test tube stopper or maybe an injection port. Mine are all PTFE. If you have a hole in your lid you could possibly build up a thicker lid by siliconing on little discs of plastic, so they form a stack maybe 1/2" high, then drill a hole through them all to put your skewer through. A heated skewer may be able to be pushed through the lot of them.
I have a few types of magnetic stirring jars, some which would easily blend up agar plates. I have a dismantled hot water pump which has a magnetic drive. There is a plastic part with turbine vanes in it which has 4 magnets held inside the plastic. The motor has 4 matching magnets and they are strong enough that I can spin the vanes when they are through a layer of glass. So I can sterilize jars with the enclosed magnets in the jars.
I also have large stainless ball bearings which are magnetic (some stainless is not magnetic). These are also attracted by the same motor with magnets and so I can spin the ball bearings in the jar at very high speed. A very simple device could be made like this. If you had magnetic stainless steel self tapping screws in your jar they would easily cut up agar. Now all you need is a strong magnet to attract them through the glass, it may be possible to just pull the magnet back and forward to blend it up. If not a magnetic stirring device could be made for a drill. You get a rod of metal, bend into an L, glue the magnet to the end of the L shape and stick the other in the drill, now you have an off centre magnet so when the drill turns the magnet spins around in a wider diameter, pulling the screw with it.
Quote: invitro said: The blades aren't sharp on the back edge though and that's what you would be working with if you spun it backwards.
My 6" blade in the large tub is folded on the non cutting sides. It rotates centrally and has folded blunt steel bent at 90 degrees about 10mm high. When the drill is ran in reverse this stirs grains, when run normally it acts like a blender, the folds also mix up the substrate so it cuts better.
I wanted this tub for sclerotia, my idea was to use rice which does not shake easy, and be able to stir and cut it up. If growing grains like rye/wheat/oats/barley I was thinking that after it is fully colonised it could be chopped up and let regrow over the now exposed grains. Exploded grains are usually said to be prone to contamination, but you would be letting it colonise fully first and be chopping up in a clean environment. I think this extra growth might be more than what you would get in a typical LC, if you strain an LC you see just how little there is, I think a large tube of fluffy airy grain might take off. Sterile water may be injected if it looks dry, and it could be chopped up again.
Moisture levels should not be a problem, you simply weigh and calculate what moisture is needed. If you saw 60g of coir need 1000ml of water to be at the right moisture level then you can add 500ml to 60g and heat treat it and add 500ml of slurry to hydrate. I often drive off moisture after adding excess water to substrates and microwave it until it drops in weight, while heat treating at the same time.
|