This thread is about the gear that I use to make my jars and bulk tubs. I followed teks written by Trusted Cultivators for my Glovebox and Jar Lids. Lets start with the glovebox. Before we even start with the glovebox, lets talk boxes for a second. I dig monotubs, and i really wanted a solid tub that i could acquire en masse. This is the tub i chose.  I selected it because it is made of a pretty thick, transparent, durable plastic, has a snap on lid, and has a gigantic surface area. Here it is applied to Roadkill's Still air box tek.
To make the holes i used my 2" hole saw bit to cut 4 overlapping holes, the farthest edge about 3 3/4" from the other farthest edge. I then used a sharp knife to round out the hole. After inserting the plumbing fitting i sealed it up with silicone on both sides.
 I need to add the port on the back of the box with the polyfill, but i haven't found a fitting that i like yet. Props to Roadkill for an excellent design and a detailed tek on how to make it.
Here is the tub being used as a monotub with a 4" deep WBS-> Straw/Dung substrate.  So, this thing is 12.3 inches deep. Which means that with a 4" deep sub the sub only has to humidify the 8" between the sub and the lid. It does this easily, which allows you to apply massive FAE, promoting large pinsets and large flushes over the approx. 3 square feet of cropping surface that this tub offers. Check this thread for more info on this tub being used as a monotub. Props to ohmatic for inventing the monotub 
Now let me move onto my kits. I really dig being neat and organized. I smoke a lot of
ganja
, so i sometimes forget where i put things. Being organized helps me not lose things or get frustrated. It makes it easier for me to keep things clean, and i think, overall, is a good move. I like using the rectangular boxes that Ball jars come in to make kits for specific tasks. Here is my inoculation and general sterility kit.

It contains a sterile box with 10,12, and 60ml sterile syringes and a few sterile spoons in aluminum foil sheaths, micropore tape, Germ-X, 2 bottles 91% isopropyl alcohol one of which is fitted with a sprayer, hydrogen peroxide, Oust, N95 masks, sterile pads, a lighter and gloves.
Here is my lid kit.
 It contains Ball mason jar lids of every size and description, gorilla/duct/masking tapes, tyvek, drill bits/hole bit, silicone, aluminum foil, and my Wusthof shears. I used this kit to make these jar lids via Fahtster's homemade lids that have stood the test of time tek
 .
I have made about 3 dozen, i may make another dozen but i plan on upgrading to a permanent lid setup soon, which will feature synthetic filter discs and synthetic injection ports. Props to Fahtster for an excellent design utilizing materials that any cultivator would have and an excellent tek to boot 
Here is my Bulk Substrate Prep Kit
It contains lots of turkey sized Reynolds oven bags, which i double bag my straw/dung/verm/gypsum in for pasteurization, PH adjustor used to treat the water that is used to hydrate the sub, long probe thermometer for monitoring pasteurization, gloves, press'n'seal for the top of the bin (precaution), wax paper to lay on the sub for colonization, and analog hygrometers/thermometers.
All of these kits fit nicely on the lower shelves of my worktable

I cannot explain how easy these things make my life. Whenever i need to perform a task, i grab the corresponding kit, rather than looking around for the things i need. It also makes it easier for me to take inventory so i don't run out of anything. Plus everything is out of the way and in the closet. There is no evidence of cultivation visible in my home unless i am working in the kitchen.
I am new to cultivation, so i have not gotten a ton of use out of these things. I reckon i will though. Thanks for looking, any feedback/discussion is more than welcome. This is always on my mind, so i'll ask, What do you think about the subject of tub height?
-------------------- ~You're already dead, but you're about to die~
Penis Envy in Monotubs Ecuador in Monotubs
|