Auto-SummaryIn this detailed guide, user fahtster provides a step-by-step walkthrough for creating gellan gum (GG) plates, specifically tailored for mycelium transfers. Addressing a lack of clear instructional resources for this medium, the author highlights the advantages of using low-acyl gellan gum, such as increased clarity and the ability to pour at lower temperatures to reduce condensation. The post emphasizes the importance of specific procedural timing to avoid common pitfalls like clumping or premature setting. Key technical advice includes hydrating the GG in room-temperature water, mixing it with dextrose before heating, and adding calcium chloride—or alternatively, Epsom salt—only once the mixture reaches a boil. By sharing personal ratios, such as a 1% concentration for both GG and nutrients, and refining the process through community feedback, the author offers a practical, optimized recipe for mycologists seeking a firm, brittle gel surface that facilitates easier transfers.
On editing: I am making edits to this as I try different things. I’m going to leave the original intact but the edits/additions will be in bold italics
Yoyoyo… obviously nothing new here, so to speak but I started to use gellan gum (GG) plates fairly recently and found that, while there’s lots of different recipes floating around, a straight up “here’s the steps you take” thread is lacking on the site. There is a certain order that things need to be done in because it is different than standard agar… at least the way I did agar: put everything in the media bottle and shake, then pc.
And maybe there is a way to do it fast and easy but when I tried, I ended up with huge chunks of gell floating around in my bottles when I was ready to pour.
Feel free to school me on some better ways if you have em.
I’m going to keep things short and simple or at least try to. I’m also going to assume you already have the basic plate making materials and have poured your own agar before. Also, that you’ve researched what gellan gum is. The benefits are a clearer medium and I find you can pour at a lower temp than agar which reduces condensation a lot. The GG sets up quicker, the firmer you make it so, keep that in mind. I start pouring around 115-118F with this recipe. When I did a much softer gell set, it didn’t set up until around 95F
I like the GG to be on the firmer side.. this helps a lot with transfers as I do mostly aerial myc transfers. The tuft tends to release from the scalpel tip much easier when the surface is firm.
So here’s the gellan gum I use.. being that I want a more brittle gell, I use low acyl.

They recommend 10g per 500ml. I find that to be excessive.
For ease and to keep things simple, I just go with 1’s.. I’ll use 1% for both the GG and nutrient (I’m doing pan plates) and for the calcium chloride, I use .001%
I use potato dextrose broth as my nute source. I do use milkboys French press method which works great.. I don’t let the water settle tho; I want those bits of flakes
I use distilled room temp water. Some GG recipes say you should use ice water. I find that’s not necessary but you DO NOT want to add the GG to hot or warm water. Room temp is fine. The GG needs to be fully hydrated before heating up. More on that in a bit
For the potato broth, I use Bob red mills instant potato flakes. I put about 625ml of water into the French press and add 2 tablespoons of the flakes. I use a whisk to mix the flakes up. I’ll leave them sit for a while, whisking occasionally to soak and break up as much as they’re going to.
When I push down on the press, there will still be tiny pieces that make it through the screen.

I know some ppl that filter this water to get rid of those bits but it seems like what’s the point of doing the flakes if you’re going to filter it back out. So this will leave a tiny bit of cloudiness to the plates if you leave it in but it’s not much
Now some of the water will remain with the flakes so I pour it back into a media bottle to get an accurate amount of water

I pour that 500ml into the pan and add the rest of the distilled water I’m going to be using. In this case I made 1200ml total.
Now with the total potato water in the pan, I add the dextrose. Keeping to the 1%, I added 12g. This is the dextrose I use

You want to make sure you add the powdered nutes to the water and dissolve it before you add the GG. Gellan gum will instantly form a gell ball around any powders added when it’s already in the water.
The pan is not on the heat yet.. it should still be at room temp.
Now you add the GG… also staying to the 1%, I weigh up 12g. Now this is already in clumps in the container.. you want to break these clumps up into as fine a grade as possible. I do this by putting it a sandwich bag and breaking it up with my fingers.
mix the dextrose and GG together in the baggie and shake the shit out of it. Adding both together seems to keep the clumping to a minimum or at all if whisked in slowly
When it hits the water, it’ll form gell balls around itself so you need to pour it into the water VERY SLOWLY. I do this by cutting one of the corners off the baggie and tapping my fingers on the side of the bag with one hand while the other briskly whisks the powder in

Even when you add it super slowly, you’ll still end up with some small clumps.. those are easily broken up when high heat is reached… large clumps, not so much.

I recently tried Epsom salt instead of the calcium chloride and I like it much much better. The clarity is even better with the ES and I was able to let the GG cool about 15F more before it started to set

ES on the left.
I did have to use more ES than the CC… I did .0017% and got the same firmness as the plates where I used CC. Also used Strawboys method and put a 1/4 cup of the potato dextrose/gellan liquid aside before heating and dissolved the ES in that before adding it to the boiling mixture
End of edit
There’s one last ingredient and thats calcium chloride to make the gellan gum set properly. I went off strawboys recommendation for the calcium chloride but I’ve seen other materials be mentioned like epson salt and these mentioned by fantastic Mr Fox
“When making the Gellan gum gels you need to add a source of positive ions, like magnesium chloride, sodium chloride, or Calcium chloride in order to bind the molecules together and make the gel set since Gellan gum is ionic but only possesses negative ions.”
This bottle of CC should last me the rest of my life 

Staying with the .001%, I weigh out 1.2g

Don’t add the CC yet. If you add it to the room temp GG broth water, any GG that touches those pellets will instantly turn to a solid gell and low acyl GG doesn’t melt back down. You need to add the CC when the broth is at boiling temps
Put the heat on high for the pan and bring to a boil. Add the CC and whisk it in to dissolve.
You should have a thinner clear liquid where all the GG is dissolved. Be careful of boil over.
I transfer this liquid into a large bowl that has a pour ring

If I tried funneling it into my media bottles from the pan directly, there would be a ton of spillage. The pour ring is crutial.
Here it is in the media bottle

Now pc and pour. Your plates should come out this clear. If you omit the potato broth or filter it, it’ll be even clearer

Again, I’m pretty new to GG plates and it took me a few times to get it where I like it. If anyone that makes them wants to add anything, please do. I feel like I could probably even use less GG and maybe more CC to get the same firmness I want but I’m unsure and pretty satisfied with the results and the ease of the ratios but any insight from those that have experience with it is more than welcome.
Edit: here’s some great input by strawboy for an even smoother process
Quote: strawboy said: I blend gellan gum and pdb powder first and then whisk it into cold water. This pretty much eliminates any clumping. Also Calcium chloride rapidly absorbs water from the air and becomes a little sticky. I reserve 1 TBSP of the water and dissolve the CC first. Whisk the gg and nutrient mixture into the water. Bring to a boil and simmer for at least 2 mins then pour in the dissolved cc.
^^^ I did all these suggestions from strawboy and they worked great
|