Home | Community | Message Board


This site includes paid links. Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Shop: Sporeworks.EU Spores for European Microscopy   North Spore Cultivation Supplies   MagicBag.co All-In-One Bags That Don't Suck   Unfolding Nature Unfolding Nature: Being in the Implicate Order   Original Sensible Seeds Bulk Cannabis Seeds   Myyco.com Isolated Cubensis Liquid Culture For Sale

Jump to first unread post Pages: | 1 | 2 | 3 | 4 | 5 |  [ show all ]
Re: Building a 650 Liter autoclave [Re: deadmandave]
    #29641247 -

deadmandave said:
Damn I didn't think about the lid opening with all that stuff on it. How does it feel? Any chance of accidently smashing something?

The over pressure safety is great. Wonder if there's a way to have it send you a message.

Idk how you feel about it but I often leave my autoclave alone for a while after it's going.





I haven’t opened it yet since installing the new devices, I need to put matching torque marks on all the bolts first now that they are at optimal tolerance since it hasn’t been opened after the 50psi leak down test so I know that’s the best bolt torque the issue is that I also still need to sand and paint so I might need to engrave the match marks first,

My biggest concern would be the clearance issue if I didn’t set the controller panel low enough but that’s easy enough to fix, I can just weld in catch plates that stop it from opening 180° and instead hold it open at 120°



I could definitely connect an arduino with WiFi to send me text alerts :lol:
But I don’t think I’ll get that fancy yet, maybe in the future but more then likely I’ll just map a few cycles until i find a good run time based on load density and use that to set up an automation system so it just runs itself with out human Intervention


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29641320 -

Awesome work man, that thing is a beast!

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: hummingbird]
    #29641501 -

hummingbird said:
Awesome work man, that thing is a beast!




Thanks !!!!

I’m excited and terrified all at the same time :rofl2::skol:


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29642042 -

I changed the single red wire conductor I had going to the low water cut off (LWCO)  sensor to a metal clad cable with 3 14AWG conductors in it one is a 24v chassis ground and the white is just caped off, the black is used for the sensor signal wire and I routed it cleanly around the side so it’s out of the way







Also salvaged an old 60A Non-fused throw handle disconnect from my electrical scrap pile lmao and wired the female plug load side so it’s ready to install in the cinder block building




--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29642610 -

I fabricated some lid flanges to seal my intake vacuum breaker filter from cut and polished aluminum, funny enough it’s actually the cover off a 400A meter base I was going to scrap but figured this would be more fitting to repurpose it

The plan is to run my 3/8 inch by 6 inch pipe through the center of both plates and then cap the pipe end and that will sandwich it all together, I’ll also apply silicone to form a gasket and then drill holes in the pipe where it will be open inside the sealed filter body only allowing filtered air






And I added some more indicator lights to the instrument panel for LWCO and over pressure indicator

I plan to put labels for each fault light and green is obviously fully operational

I still want to add an on off switch at the control panel but not sure which style to go with



--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29642640 -

Looking good. Was curious how the Air filter was going to come together, I like your idea.

Will you be rolling it into the lab after the cook? How much weight will that be?

If it proves unruly you could weld a hitch on it and use an electric trailer dolly to drag it around.

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: deadmandave]
    #29642766 -

deadmandave said:
Looking good. Was curious how the Air filter was going to come together, I like your idea.

Will you be rolling it into the lab after the cook? How much weight will that be?

If it proves unruly you could weld a hitch on it and use an electric trailer dolly to drag it around.



I do have future plans to weld a detachable trailer hitch but my budget is getting thin, I have to buy a sheet of stainless steel to fabricate a lift basket I can use an overhead hoist with but the 16 ga 4x8 sheet is $400 alone not including welding fees so now I’m pushing $3k with this project

:vaped:



I actually found a much better work around instead of unloading in the lab/clean room…….. not to mention it will bypass all the repetitive and tedious process of opening, folding, grain transfer, sealing, shaking etc etc and honestly it makes the vacuum filter unnecessary and redundant,

I don’t know why western culture and America in particular hasn’t caught on to it yet but there’s a reason why the Asian people dominate the market

The plan is simple, change my bags from the American standard filter patch bags to the Asian standard cap and plug type bags


This simple solution will allow me to pre seal the bags with a much more breathable filter that will;

^ prevent bags from bursting reducing contamination from bad seams
^ faulty filter patches
^ vacuum intrusion from contaminants as bags cool
^ risk of introduction from open grain transfers
^ directly injected LC through the pre-sealed filter plug
^ automated filling, sealing and LC injection


This in turn makes the process of loading, cooking, and inoculating more streamlined and efficient when working at such a large volume,

I’m going to be honest there’s no way in fuck you could pay me to process 500lbs of spawn or sub using conventional methods, the western filter patch bags are built for hobbyists production at best even the automation for that system is atrocious like the Thor bagger looks great on paper but in practical applications it’s leagues behind the Chinese automated systems using cap and plug systems





--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29649640 -

Been thinking about this since you mentioned it. Asia is leagues ahead of the West as far as mush cult is involved.

I'll be very interested to see how you like it. I wonder if the automation infrastructure in Asia makes bottles more friendly overall, the worst part being washing bottles. I guess the advantage of these cap and plug bags is the automation of filing is easier, no complicated gussets to fold.

I imagine you'll work towards automating your chain of events but in my mind that's a large undertaking.

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: deadmandave]
    #29649720 -

Yes I have plans to scale and it seems to be the only logical solution to the bottleneck of American patch bags


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29681637 -

This project is so cool! Fabrication is one of my biggest fascinations and this has got to be one of the coolest things I've ever seen anyone make.

I saw you mentioned getting a torque gauge for an impact gun earlier to make the loading process quicker, and later putting torque marks on the bolts. Made me think of something that might be a little quicker and easier. They're called torque limiting extensions. They basically work by elastically deforming at a specific torque load, thereby limiting the torque output of an impact gun. That way you could just pop the extension on and let the impact bang on the bolts until it stops turning, then use the torque marks to verify. Not sure if that would meet your particular needs, but it jumped out at me as a simple and quick answer to reaching a known torque on a bunch of bolts quickly and I thought I'd share.

Good luck with the rest of the build! Can't wait to see how it comes along.

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: GymnCarrey] * 1
    #29681734 -

I actually found that to be a mistake using the impact just wasn’t actually putting enough torq preload on the bolts, had lots of leaks at the flange even with the impact ropes out, my welder showed me to put a breaker bar on it and I was able to get almost another full turn on every bolt before it stoped leaking, now that I have it properly torqued I plan to match mark the bolts to the flange with a physical groove or punch mark


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns] * 2
    #29685822 -



Sketched out my electrical system for the autoclave I designed it with a redundant safety loop that will protect both elements should there be a low water or over pressure event it will immediately drop out both contactor relays shutting down the power to the elements and my blow off valve will dump the load and relieve pressure at a rate faster then the elements can produce, and I have 2 separate alarm loops set up with fault lights one red for the over pressure sensor and one orange for the low water fault that also has built in buzzers so there is both visual and audible cues separate from each fault to make troubleshooting easier



I finally found a US. Based company that actually sells the correct filter-less bags that pair with the ring and collar Chinese bag caps and they are very reasonably priced so I just ordered a 50 count for $12 to test out






I had to buy my collar rings/caps separately off alibaba express, i ordered 150 caps to start with since they are reusable that should be a full load in my clave around 400 lbs of spawn

I’m still working out the details for the basket trays and hoisting system, I have changed plans here my welder made a suggestion since I already have a big roll of stainless steel mesh fence withl holes slightly smaller then rabbit wire, the plan is to use this wire to make the baskets in a 4 self system, I will need to buy stainless rod and flat bar to use as stiffeners







--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns] * 1
    #29694139 -

Trying to wrap up the electrical and safety controls made some progress, I plugged it in last night and confirmed the lower alarm works and the 24v transformer works

I’m still waiting for my latching relay to arrive Monday so I can finish the power boil circuit


Added a cooling fan since I have 2 transformers, a solid state relay, 2 contactors, plus the ambient heat that will be coming off the unit running so I don’t want anything overheating and malfunctioning











Still need to install the vacuum release filter and thermal paste to the thermowell




I also installed a momentary push start button for the power boil element with a light indicator just waiting on that relay


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29694612 -

:threadmonitor:


--------------------
"Why try for high fives,
When my pies have nine lives?"
DUBJUG : H.D. : PLASTIC-MYC : TGE : JOIN CAKE WARS : MODERN FRUITING : MCWA : QDMT : ♾️ : MY FAV TEKS 📖

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: langten69] * 1
    #29696061 -

it’s go time !!!! PID is on and the cooling fan is kicking ass!! front lid is finished and installed in place, time to run through diagnostics testing and then it’s on to welding the stainless steel drop in baskets and painting this bad bitch!! i think i might be up and running by November !!!







--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29696562 -

Glad I found this thread as I am planning build one soon.

I didn't like the price or lack of variability of colour spectrum in the market of LED grow lights so I built custom ones from scratch and they turned out to be around £100-£200 cheaper:)

:goodluck:

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: BadgerFriend]
    #29696613 -

BadgerFriend said:
Glad I found this thread as I am planning build one soon.

I didn't like the price or lack of variability of colour spectrum in the market of LED grow lights so I built custom ones from scratch and they turned out to be around £100-£200 cheaper:)

:goodluck:




Just be careful do your research on proper engineering and check your local safety codes here it’s criminal to build or operate a DIY boiler above 15psi this is why I’ve caped mine at 15psi with a emergency relief valve of 20 psi and will have it placard on the unit

The other biggest feature is that I’m on large acreage in the rural south so if there’s ever a catastrophic event I’d be the only person at risk not neighbors


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29696922 -

I have completed faith in your build. I think you could run it in an apartment.

Remember this guy? Running 5 55gal drums at 15psi. Now that's where the risk is. https://www.shroomery.org/forums/showflat.php/Number/27837692

Can't wait to see the baskets. Also curious about your inoculation technique. Will it be LC injected thru the polyfil filter?

Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: deadmandave]
    #29696965 -

Yes directly injecting LC through the polyfill plugs unless I can come up with a better alternative but the reason I’m transitioning to the Chinese bags is because I don’t have to break and shake, impulse seal, grain to grain, or open the bags at all until they are fully colonized and I plan to build out an auto bagger like the Chinese use that will preload the bags so all I need to do is cap them and load the autoclave,






I will also probably set up a chain fall or hoisting system to help load the clave, the idea is to build the infrastructure to make production as efficient as possible without human labor since that is the biggest bottle neck in American cultivation
The LC will also be brewed in 5 gallon glass carboy or metal kegs that’s been fabricated to run an oxygen bubbler and mechanical stir armature but I’ll cross that bridge later I already have a lot just completing this MOFO



I just placed an order for 120 feet of stainless steel 1/8” X 1/2” flat bar to fabricate the baskets for $200 and thats just the stiffener bars I already have a fat roll of stainless wire I think I mentioned that I’ll drop a picture here





If this build comes out good I’ll probably show case it in my portfolio and advertise to fabricate custom claves for other businesses owners since there’s practically no one else doing this, I’d like to build walk in sizes next :lol:


--------------------








Extras: Filter Print Post Top
Re: Building a 650 Liter autoclave [Re: 7Suns]
    #29696990 -

I wonder if sandman420 is still around lol I’d love to get his opinion on my build :lol:


--------------------








Extras: Filter Print Post Top
Jump to top Pages: | 1 | 2 | 3 | 4 | 5 |  [ show all ]

Shop: Sporeworks.EU Spores for European Microscopy   North Spore Cultivation Supplies   MagicBag.co All-In-One Bags That Don't Suck   Unfolding Nature Unfolding Nature: Being in the Implicate Order   Original Sensible Seeds Bulk Cannabis Seeds   Myyco.com Isolated Cubensis Liquid Culture For Sale


Similar ThreadsPosterViewsRepliesLast post
* Horizontal autoclaves? newb grower 3,236 17 07/17/08 04:13 PM
by solumvita
* The autoclave of my dreams - 75000 Euros
( 1 2 all )
FreeSporePrints 5,110 21 12/28/06 01:14 PM
by Cryogenicz
* Laundry Basket vs. Straw log jccc 1,022 2 09/14/08 05:18 PM
by jccc
* RR's Laundry Basket 'TEK' with Golden Oysters
( 1 2 all )
FugueRider 7,714 22 05/19/09 10:22 PM
by FugueRider
* anyone seen good prices on small autoclave or retorts? Imorph 1,946 3 01/17/04 01:22 AM
by Imorph
* Vitamin B1 (thiamine hydrochloride) and autoclaving wbastz 6,438 3 05/31/09 06:33 PM
by wbastz
* Autoclave pics
( 1 2 3 all )
crazyredhead 10,417 47 01/13/03 01:27 PM
by Anno
* grey oysters - visions laundry basket zeegos 4,927 18 03/08/07 04:42 AM
by zeegos

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: RogerRabbit, cronicr, Pastywhyte, Forrester, Stromrider, SHROOMSISAY01
1,384 topic views. 0 members, 18 guests and 7 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:

Copyright 1997-2026 Mind Media. Some rights reserved.

Generated in 0.034 seconds spending 0.006 seconds on 18 queries.