Home | Community | Message Board

Reliable Spores
Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Shop: Bridgetown Botanicals CBD Edibles   PhytoExtractum Kratom Powder for Sale

Jump to first unread post Pages: 1
InvisibleHeruuka
member
 User Gallery
Registered: 10/16/99
Posts: 333
Adhesives that Withstand Autoclaving
    #948523 - 10/10/02 07:53 AM (18 years, 11 months ago)

I tried hot glue (stupid, and obvious) i tried regular silicone- no go, and ive tried wood glue - flop!

Which adhesives hold @ 121 C? i was thinking high temp. silicone but its too expensive. I intend to glue filter disk ala Micron Magick to metal or plastic.

H


Extras: Filter Print Post Remind Me! Notify Moderator Top
OfflinePoogi
Stranger
Registered: 07/13/02
Posts: 610
Last seen: 14 years, 8 months
Re: Adhesives that Withstand Autoclaving [Re: Heruuka]
    #948529 - 10/10/02 07:55 AM (18 years, 11 months ago)

Most epoxy should. Most hardware stores should carry some form of it. It's pretty cheap, runs somewhere around $2.50 for a tube.


Extras: Filter Print Post Remind Me! Notify Moderator Top
OfflineDERRAYLD
Constructus
Male

Registered: 05/13/02
Posts: 3,326
Loc: South Africa
Last seen: 4 hours, 49 minutes
Re: Adhesives that Withstand Autoclaving [Re: Poogi]
    #948532 - 10/10/02 07:58 AM (18 years, 11 months ago)

You could use a heat resistent silicone as well.


Extras: Filter Print Post Remind Me! Notify Moderator Top
Offlineblackout
 User Gallery

Registered: 07/17/00
Posts: 5,111
Last seen: 26 minutes, 26 seconds
Trusted Cultivator
Re: Adhesives that Withstand Autoclaving [Re: DERRAYLD]
    #951387 - 10/10/02 11:34 PM (18 years, 11 months ago)

normal silicon always works for me. rub it well into the disk and stick it from both sides


Extras: Filter Print Post Remind Me! Notify Moderator Top
OfflineShaw
hick

Registered: 06/28/01
Posts: 2,220
Loc: midwest, usa
Last seen: 9 months, 12 days
Re: Adhesives that Withstand Autoclaving [Re: Heruuka]
    #957924 - 10/13/02 09:43 PM (18 years, 11 months ago)

if it absolutly comes down to it, jb weld has worked on my muffler for a while now. it's a bit messy though.


--------------------


Extras: Filter Print Post Remind Me! Notify Moderator Top
InvisibleMilletV
--intransition--

Registered: 01/09/02
Posts: 251
Loc: Rockies
Re: Adhesives that Withstand Autoclaving [Re: Heruuka]
    #957952 - 10/13/02 09:51 PM (18 years, 11 months ago)

100% silicone sealant will work, but you have to let it cure for at least 24 hours before p cooking it or it wont hold up. It will also stick to foil if its not been cured long enough.

To make it stick to the plastic lid rough the area around the hole up really good with course sandpaper, then wipe the lid with alcohol.

Once the alcohol evaporates you can put the silicone on and it will stick to the plastic well.

MM


Extras: Filter Print Post Remind Me! Notify Moderator Top
Jump to top Pages: 1

Shop: Bridgetown Botanicals CBD Edibles   PhytoExtractum Kratom Powder for Sale


Similar ThreadsPosterViewsRepliesLast post
* Making your own autoclavable bags Anonymous 5,989 17 05/15/03 08:28 PM
by Amanita_Dreamer
* Autoclavable Bags Parafreak 1,721 10 09/20/01 10:29 AM
by Pinhead
* "Microwave sterilized media supports better microbial growth than autoclaved media"
( 1 2 all )
blackout 5,358 32 02/14/15 02:08 AM
by hoffzl01
* Commercial Autoclave Use
( 1 2 all )
Aquamon 6,806 38 10/23/12 10:14 AM
by Aquamon
* Autoclave to replace pastuerization vaporbrains 2,075 12 10/19/02 10:12 PM
by MsPacMan
* Autoclaving substrate with high motor oil content (<10%) Kryptos 1,193 12 10/22/16 02:38 PM
by Lennybernadino
* making autoclave bags matts 2,791 10 06/02/04 05:31 PM
by Gr0wer
* Dry heat autoclave? jrizzle385 2,720 3 12/17/10 06:09 PM
by MushroomProspector

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: RogerRabbit, cronicr, Pastywhyte, bodhisatta
3,306 topic views. 1 members, 3 guests and 3 web crawlers are browsing this forum.
[ Print Topic | ]
Search this thread:

Copyright 1997-2021 Mind Media. Some rights reserved.

Generated in 0.048 seconds spending 0.028 seconds on 13 queries.