|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
jonogt
Jon

Registered: 12/27/07
Posts: 104
Last seen: 15 years, 7 months
|
those legit medical supply injector site plugs and little filters?
#7956835 - 01/30/08 05:42 PM (16 years, 2 days ago) |
|
|
I saw a tek on here where someone had used them (for an LC i beleive it was). I can't find the picture or the tek anymore for the life of me of course though and I don't know the correct term for the things. the injection plugs are like the rubber things that are on top of drug bottles in hospitals and pharmacies. they can't be to expensive they're just rubber. the filters im not sure about. I asked about them at a lab supply store i go to once in a while and the only thing they sold were these BIG fuckin things that were like a cylinder 1 inch diameter and atleast 2 inches tall. they looked to be similar in material to what i saw in the tek here though. the ones on here looked like maybe the diameter of a penny though, and were installed on the jar lids in similar fashion to the injection sites.
can these filters protect against contaminants getting in if you slosh some of your LC solution up against em? I know with polyfill everyone says you gotta make sure not to do that cause it can whick contams in. The guy at the lab supply store said the ones they sold can filter liquid if its pushed through under pressure. i'd ration that if they filter air to 0.2 micron, and liquid has to be put through under pressure, that a) you'd have to shake the hell out of it to get your solution whicked up through it and into the outside world. and b) if it did whick through, the fact that it stops things over 0.2 microns wide from passing would keep any contams from movin in as a result. c) if you pumped distilled water through em between LC batches, couldn't they be reused a fair amt of times? d) being able to not worry about getting that wet would be nice cause you could agitate the things a lot more effectively.
^^is my rationale correct? what are these things officially called? or a link to the tek? where can i buy em at?
w/e info you got on the subject is appreciated. if they are as effective as i'm beleiving they are and i can get em locally, i'd be real interested in that over polyfil.
|
tahoe
Noob Slayer



Registered: 11/26/03
Posts: 6,274
Loc: N38.93829W119.98108
|
Re: those legit medical supply injector site plugs and little filters? [Re: jonogt]
#7956852 - 01/30/08 05:45 PM (16 years, 2 days ago) |
|
|
maybe search for "The Only LC Tech! The Liquid Culture How To Guide "
-------------------- Stop experimenting half way through your first grow. Grow it to maturity, watch it, learn from it. Do this a few times then experiment with different ideas and figure out what works best for you.
My Legacy https://www.shroomery.org/forums/showflat.php/Number/22140987#22140987 Teh=The I need to proofread
|
kupa trooper



Registered: 11/11/07
Posts: 750
Loc: Earth
|
Re: those legit medical supply injector site plugs and little filters? [Re: jonogt]
#7956873 - 01/30/08 05:48 PM (16 years, 2 days ago) |
|
|
I think I got mine at lab surplus the injection ports that is. As for the filters i make my own with fish tank tube and pollyfill with no contam or prob. this is what it looks like
-------------------- I don't know but I've been told. It's hard to run with the weight of gold On the other hand I heard it said. It's just as hard with the weight of lead.
|
blood4blood
Calmer Than You Are


Registered: 04/25/07
Posts: 6,029
Loc: The Valley
|
Re: those legit medical supply injector site plugs and little filters? [Re: kupa trooper]
#7957756 - 01/30/08 08:40 PM (16 years, 2 days ago) |
|
|
http://www.shroomery.org/forums/showflat.php/Cat/0/Number/7887928/an/0/page/0/gonew/1#UNREAD
next time you run into a rocking tek that you might revert back to for info or a good refresher, bookmark it. then you'll never have to ask again yo.
|
jonogt
Jon

Registered: 12/27/07
Posts: 104
Last seen: 15 years, 7 months
|
Re: those legit medical supply injector site plugs and little filters? [Re: blood4blood]
#7957990 - 01/30/08 09:35 PM (16 years, 2 days ago) |
|
|
ya i almost always do bookmark em but i just forgot that one. thanks for the links maybe i just missed it in there, but are those syringe filters ok to get wet on the inside and not get contaminated?
|
blood4blood
Calmer Than You Are


Registered: 04/25/07
Posts: 6,029
Loc: The Valley
|
Re: those legit medical supply injector site plugs and little filters? [Re: jonogt]
#7959181 - 01/31/08 05:38 AM (16 years, 1 day ago) |
|
|
i wouldnt get any of them wet imo. if you only fill your lc jars half full or so and put a piece of glass in them (to break up the mycelium) when you go to shake them just give them a little tornado spin and the liquid will stay off the top. you dont want to be vigourlsy shaking your lc jars.
also when you extract the lc you should be able to tip the jar just so the liquid covers the extraction port and not getting the filter wet either.
|
flushme
Shroomery OG



Registered: 03/15/07
Posts: 2,374
Loc: Kazakhstan
Last seen: 10 years, 3 months
|
Re: those legit medical supply injector site plugs and little filters? [Re: blood4blood]
#7959386 - 01/31/08 08:12 AM (16 years, 1 day ago) |
|
|
http://www.smallparts.com/products/descriptions/m27.cfm and the rubber stoppers can be found in the lab supply link in my signature
-------------------- TRUST IN THE FLUSH
 Take Salvia Cuttings Successfully
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 771 topic views. 15 members, 130 guests and 34 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|