|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
tony8404
Stranger


Registered: 06/14/05
Posts: 1,323
|
trying to pin point failure with lc
#7903938 - 01/19/08 10:54 PM (16 years, 13 days ago) |
|
|
okay, i am going to try to nail my problems with LC.
I am going to first, be very sterile this time... last few times i was not very sterile...
i am going to boil in a medium sauce pan a small baby bottle and a half pint mason jar for about 30 minutes... then i will cover with some paper towels that have been sprayed with lysol.
then i will reheat the water in the sauce pan for another 15minutes or i mean boil.. then once that is done i will put the correct amounts of water in the mason jar and baby bottle.
i think with the mason jar i will use 220cc water and 1 packet of raw sugar.
after i add the water i will add the sugar and then stir for a minute or two for the sugar to disolve. then i will pc them both at 15 psi for 20 minutes...
i will then let it sit all day till like 10 at night and then inoculate with a un used spore syringe i have not opened yet but i will first spray the room with lysol sit for a minute and spray again wipe stuff down and then inoculate i am planning on doing this early like 7 a.m. i think the baby bottle i will use honey, the baby bottle is small so i only use 100cc of drinking water, what amount of honey should i use to be correct cause i think this was a problem i wasnt catching.. thanks
|
Crasher
αἱρετίζω




Registered: 03/13/01
Posts: 6,220
Loc: Tardy to the Party
|
Re: trying to pin point failure with lc [Re: tony8404]
#7903954 - 01/19/08 10:58 PM (16 years, 13 days ago) |
|
|
Good luck.
-------------------- Give me silence, water, hope; Give me struggle, iron, volcanoes...
|
tahoe
Noob Slayer



Registered: 11/26/03
Posts: 6,274
Loc: N38.93829W119.98108
|
Re: trying to pin point failure with lc [Re: tony8404]
#7903961 - 01/19/08 10:59 PM (16 years, 13 days ago) |
|
|
if you have a pc than do not waist your time with all that boiling.
Here is what I do. quart jar, 500ml of tap water, 1 gram of powdered malt, pc 15-20 mins at 10-15 psi, Let cool. Either use spore syringe in the open with no glove box or nothing. i do not like spore syringes on a lc.
Or bust out the glove box and scrape a goo chunk of mycelium off of a petri and open the lid to the lc and dump it in. 100% success. Do not waist your time with all that boiling.
5 mins in a pc at 15psi is better than 30 mins boiling at 0psi
-------------------- Stop experimenting half way through your first grow. Grow it to maturity, watch it, learn from it. Do this a few times then experiment with different ideas and figure out what works best for you.
My Legacy https://www.shroomery.org/forums/showflat.php/Number/22140987#22140987 Teh=The I need to proofread
|
DJYoshaBYD


Registered: 04/07/07
Posts: 2,405
|
Re: trying to pin point failure with lc [Re: tahoe]
#7904194 - 01/20/08 12:18 AM (16 years, 12 days ago) |
|
|
LC is boosty as fuck... just noc up grain and spawn it.. LC is overkill, in my opinion... you can do a great job spawning some rye to coir or straw or poo or whatever combo you make...
LC is a pain in the ass... if you cant get it to work, then try a grain tek.. tell me which one is easier...
thats just one lonely lil DJ's opinion..
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 432 topic views. 14 members, 156 guests and 25 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|