| Home | Community | Message Board |
|
You are not signed in. Sign In New Account | Forum Index Search Posts Trusted Vendors Highlights Galleries FAQ User List Chat Store Random Growery » |
This site includes paid links. Please support our sponsors.
|
| |||||||
|
Anonymous #1 |
| ||||||
|
MARSOFOLD TEK
Amazing simple clean DMT extraction How to easily extract DMT: ======================= Break 1-Pound of Mimosa Hostilis rootbark into 2" pieces and grind it all up in a glass-topped blender, a little at a time. -------------------------------- Polar Extraction: Premix in an empty 1-Gallon plastic jug: 1-Quart White Vinegar & 3-Quarts Water. Put the ground up Mimosa in a 3-Liter crockpot, then fill it with the water-vinegar solution. Stir well and turn it on "high". After 2 hours, remove the crockpot ceramic liner, hold the lid on slightly offset, and pour off most of the liquid into a 1-gallon wide-mouthed glass or stainless container. Add the remaining water-vinegar solution to the crockpot again. Stir well and turn it on "high". After 2 hours, remove the crockpot ceramic liner, hold the lid on slightly offset, and pour off all of the liquid into the same container again. Discard the rootbark fiber and save the two combined extractions in the 1-gallon container. Allow the vegetable particles in the extraction in the 1-gallon container to settle to the bottom overnight. Then pour off the liquid into an empty 1-Gallon glass wine jug, being careful not to pour off any of the vegetable sludge at the bottom. Discard the sludge and keep the contents of the wine jug. -------------------------------- Basification: Premix in advance a solution of: 5 Tablespoons (63grams) of Sodium Hydroxide ("Red Devil" lye) with 1-Pint of WARM Water. Stir well. Slowly add this solution to the wine jug, then cap the jug. Gently tilt the wine jug back and forth for 1 full minute to mix the contents. -------------------------------- Nonpolar Extraction: Add 250ml of (Ace Hardware)VM&P Naptha to the wine jug. Add exactly enough warm water to the jug to raise the liquid level to an inch below the top, then cap the jug. Gently tilt the wine jug slowly back and forth for 5 full minutes to mix the contents. Allow the jug to sit undisturbed on a table for at least 4 hours. There should now be two layers visible in the jug, a lower dark one and a smaller clear one on top filling the neck of the jug. Use a glass turkey baster to suck up the top clear layer into a pint mason jar. Be careful not to suck up any of the lower brown/black layer into the mason jar. -------------------------------- Freeze-precipitation/wash: place the sealed mason jar in a FREEZER for 3 days to precipitate the crystals. Prepare a filter setup by placing a funnel into a quart mason jar and putting a small coffee filter paper into the funnel. Shake the naptha in the mason jar strongly to stir up all the crystals at the bottom and quickly pour while still very cold into the funnel for filtering. Impure yellow-white DMT crystals will be seen on the coffee filter paper. Allow the crystals to completely dry out on the filter paper in the funnel. Premix a wash solution by mixing equal parts of Distilled Water and NON-SOAPY clear Ammonium Hydroxide(Ace Hardware Janitorial Strength Ammonia) into a pint container. Slowly pour 100ml of the wash solution over the crystals (still in the filter paper) to wash them. Remove the filter paper from the funnel, spread it out flat and allow the crystals to COMPLETELY dry out. You will now have 2-1/2 grams of white crystal DMT. At least 50 strong doses. Mix it with some parsley and smoke a little in your favorite pipe! [u]STRAIGHT TO BASE QUICKTEK Extraction Procedure 1. The first step is to pulverize the bark until it's just fiber and pink/purple dust. It should be snapped into small pieces and run through a coffee grinder or blender at high speed. You may need pruning shears to cut the bark small enough to grind properly. It needs to be completely broken down. The dust created is very fine and astringent to the respiratory tract. Unless you dig big cakey purple boogers, wear a mask. 2. Mix 15ml water and 1g lye per gram of bark in the mixing jar. For example: 50g bark would require 750ml water and 50g lye. One level tablespoon of lye weighs about 15g, though this can vary considerably, better to use a scale. Note that lye is dangerous. Blind you forever dangerous. Wear eye protection and have a bottle of vinegar handy as a neutralizer and for clean up. Add the lye to the water slowly stirring constantly until completely dissolved. 3. Add the bark, cap and shake the jar and let the bark soak for awhile. An hour or so. 4. Now add 1ml naptha per gram of bark in the mixing jar and turn the jar end over end. Do not shake or splash or there will be a tendency for the solution to form an emulsion. Simply roll the naptha around in the bark solution. Do this for one minute and then let the jar stand until the naptha has pretty much separated to the top. Repeat agitation three more times. 5. After the final agitation, separate the two layers. The naptha (top layer) goes in one of the collection jars, the rest stays in the mixing jar with the bark. 6. Put the collection jar in the freezer. 7. Repeat steps 4 to 6 three more times. Leave the last NP extraction in the jar for a day or two, agitating occasionally to pick up any strays. 8. Go to bed. You should have a collection of snow globes waiting for you in the morning. 9. Pour each jar of naptha out through a coffee filter. Save the naptha, which can be reused in the next batch or evaporated down producing a residue which can be further refined (see recrystallization below). A lot of paste will stick to the sides of the jar, so use a small rubber spatula to scrape the sides down onto the filter as well. Spread each filter out to dry. There will still be some residue in the jars, a bit of Salvia or MJ will scrub them out nicely. 10. Once the paste has dried THOROUGHLY (chop and stir it a couple of times), crush any lumps up and combine it all into one coffee filter. Now wash the lot by pouring freezer temperature NON-SUDSY ammonia over it and through the coffee filter. This will remove any remaining lye and some other impurities from the extract. If you can get 10% ammonia ("janitorial strength") all the better. Most important, though, is NON-SUDSY: shake the bottle, if it suds, get a different bottle. It won't take much, 100ml or so for a 200g batch, just make sure all the powder is thoroughly wetted, and stir it around while washing. A good bit of the mass will wash away (25-45%) but it's nothing you want to be smoking anyway. (Note: if you intend to recrystallize, you can omit the ammonia wash). You should be left with somewhere in the vicinity of 0.5% of the weight of the root-bark in DMT powder. It is perfectly smokable at this point, but it can be refined further by recrystallization. Although recrystallization inevitably results in loss of goods, once you've had a hit of DMT that left absolutely NOTHING behind in the pipe, you won't want to use anything else.
| |||||||
| |||||||
|
| Extra information | ||
| You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled Moderator: trendal, Shroomism, george castanza, Alan Rockefeller, yogabunny 672 topic views. 0 members, 1 guests and 0 web crawlers are browsing this forum. [ Show Images Only | Sort by Score | Print Topic ] | ||

