|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
TheMan420
ShroomDust



Registered: 07/02/07
Posts: 195
Loc: Around the world
Last seen: 9 years, 9 months
|
Does the "A Simple Cutless Incubator" work well
#7628364 - 11/12/07 10:55 PM (16 years, 2 months ago) |
|
|
OK before i begin i would like to say that I'm not a beginner but not an expert, ive done the Pf tek a few times all successful. Now I'm wondering if this "A Simple Cutless Incubator" tek for an incubator/grow chamber would work well. so far ive tried to make my aquarium into a chamber but it loses the heat or i have to have 2 heating mats to keep it at 80 degrees Fahrenheit, also i have no idea how my humidity pump well get it humid enough for the 29 gallon tank. If i use this tek and implement the reptile humidity pump with, it should do just fine with incubating and fruiting? Do you agree? if not why? also what size rubber-maid containers should i get? The only reason I'm asking is i want to do this right after countless failures to make my own. Info: 7 half pint jars of Psilocybin Amazon strain.
-------------------- Find Your Mind
|
Seventy
equanimitor



Registered: 05/24/07
Posts: 912
Loc: Canada (PNW)
Last seen: 6 months, 28 days
|
Re: Does the "A Simple Cutless Incubator" work well [Re: TheMan420]
#7628457 - 11/12/07 11:21 PM (16 years, 2 months ago) |
|
|
1. Use a rubbermaid bin with 3-4 inches of perlite, drill holes in the sides for FAE 2. Don't heat the FC, heat the room that it's in so you don't get excess condensation
|
MarlboroMan
Stranger




Registered: 05/01/06
Posts: 184
Loc: Tx
Last seen: 16 years, 8 days
|
Re: Does the "A Simple Cutless Incubator" work well [Re: Seventy]
#7628737 - 11/13/07 01:44 AM (16 years, 2 months ago) |
|
|
Try the TiT Tek for incubating. It works very well and I personally don't see why anyone would use anything else. As far as a FC, go with what Seventy said. You don't want high humidity in the incubator, and as far as the size of Rubbermaids, that all depends on how much you are going to be growing and how much space you have to put them in.
-------------------- I'll make it to the moon if I have to crawl..
|
TheMan420
ShroomDust



Registered: 07/02/07
Posts: 195
Loc: Around the world
Last seen: 9 years, 9 months
|
Re: Does the "A Simple Cutless Incubator" work well [Re: MarlboroMan]
#7629746 - 11/13/07 10:46 AM (16 years, 2 months ago) |
|
|
Ok so i really should use two separate containers for incubating and fruiting(rubber maid can work for both?) Ok incubator question the TiT is the tank with a submersible heater with a temperature gauge and a tank on top with water in it right? And the fruiting chamber ill cut a part off the top and get Plexiglas with some glue and glue it down, then place a space heater to keep the room in 68-70 degrees Fahrenheit with the reptile humidity tank and air pump attached to the FC with holes drilled in it for FAE- do i need to use some sort of filer?
-------------------- Find Your Mind
Edited by TheMan420 (11/13/07 10:48 AM)
|
MarlboroMan
Stranger




Registered: 05/01/06
Posts: 184
Loc: Tx
Last seen: 16 years, 8 days
|
Re: Does the "A Simple Cutless Incubator" work well [Re: TheMan420]
#7629797 - 11/13/07 10:55 AM (16 years, 2 months ago) |
|
|
Exactly. And I'm guessing you meant 'filter', and not necessarily, but if you can get some polyfil to fill the holes it would probably help keep contams out a little easier. I've never used it and have had good success, but some people like it.
TiT
-------------------- I'll make it to the moon if I have to crawl..
Edited by MarlboroMan (11/13/07 10:58 AM)
|
TheMan420
ShroomDust



Registered: 07/02/07
Posts: 195
Loc: Around the world
Last seen: 9 years, 9 months
|
Re: Does the "A Simple Cutless Incubator" work well [Re: MarlboroMan]
#7632758 - 11/13/07 09:27 PM (16 years, 2 months ago) |
|
|
ok its al systems go from here, hope it works as good as i think it will!will get back with the results when its time for fruiting!!
-------------------- Find Your Mind
|
MarlboroMan
Stranger




Registered: 05/01/06
Posts: 184
Loc: Tx
Last seen: 16 years, 8 days
|
Re: Does the "A Simple Cutless Incubator" work well [Re: TheMan420]
#7632814 - 11/13/07 09:39 PM (16 years, 2 months ago) |
|
|
Awesome bro good luck!
-------------------- I'll make it to the moon if I have to crawl..
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 676 topic views. 18 members, 189 guests and 42 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|