Home | Community | Message Board

Mushrooms.com
Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Shop: North Spore North Spore Mushroom Grow Kits & Cultivation Supplies   Left Coast Kratom Buy Kratom Extract, Kratom Powder For Sale

Jump to first unread post Pages: 1
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
OfflineCode
addict
Registered: 04/12/99
Posts: 190
Last seen: 21 years, 3 months
Re: spore making tek
    #72667 - 01/23/00 09:03 PM (22 years, 8 months ago)

Yes, you can do this. My prefered method is to punch a hole in the lid of the jar through which is threaded a bit of wire. Cover the hole with tape, put the desired amount of water in the bottom of the jar, close it up, sterilize and allow to cool.

When you are ready to make the print, take a mushroom cap, open the jar, push the wire through the center of the cap, and bend it so that the cap cannot slid off. Close the lid and leave for a day or so.

Alternate methods involve using a wire mesh for the cap to sit on rather than hanging from the lid.

You can also print the cap in the bottom of the jar without water. The sealed jar can be stored longer than if it were a solution. Simply add water and scrape the print from the bottom of the jar.



Extras: Filter Print Post Top
InvisibleRyche HawkV
A Messenger
Male User Gallery

Registered: 03/01/01
Posts: 2,112
Re: spore making tek [Re: Code]
    #72669 - 01/23/00 09:29 PM (22 years, 8 months ago)

.


--------------------
-Peace-

High Quality MUSHROOM SPORES and CULTURES  for microscopy at www.muShrooms.com



muShrooms.com is the new web site of
www.thehawkseye.com


Edited by Ryche Hawk (06/06/17 03:09 AM)


Extras: Filter Print Post Top
Anonymous

Re: spore making tek [Re: Code]
    #72670 - 01/23/00 10:24 PM (22 years, 8 months ago)

what i do is take tin foil and make a valley in side the jar,cut hole about smaller than mushroom cap ,place cap ,put the lid back on remove after spore drops.


Extras: Filter Print Post Top
Jump to top Pages: 1

Shop: North Spore North Spore Mushroom Grow Kits & Cultivation Supplies   Left Coast Kratom Buy Kratom Extract, Kratom Powder For Sale


Similar ThreadsPosterViewsRepliesLast post
* Marx2K's Tek. Let me know what you guys think.. ( marx2k 5,117 8 06/13/11 12:32 AM
by scatmanrav
* storage of prints XAZIA 4,544 11 01/25/05 09:20 PM
by PlaCoFuGostei
* Using spore prints Droog 1,918 12 10/12/01 02:18 PM
by Droog
* strange print Papa_Smurf 784 4 02/06/02 06:35 AM
by Papa_Smurf
* DOH!!! Fried Spores mrshrums 1,005 8 02/23/02 08:41 PM
by bluhoney
* Print Question FungusBoi 636 1 10/10/01 08:54 PM
by babyshroom
* making own spore syringes AzulAgave 1,991 11 12/26/01 10:24 PM
by _JJ_
* Re: 1 print = ? syringes Dystopian Harbinger 948 6 04/21/01 09:17 PM
by Taz

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, FooMan, mushboy, fahtster, LogicaL Chaos, 13shrooms, stonesun, wildernessjunkie, cronicr, Pastywhyte, bodhisatta, Tormato
874 topic views. 35 members, 240 guests and 72 web crawlers are browsing this forum.
[ Print Topic | ]
Search this thread:

Copyright 1997-2022 Mind Media. Some rights reserved.

Generated in 0.022 seconds spending 0.009 seconds on 15 queries.