|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: myndreach]
#6947763 - 05/21/07 03:28 PM (16 years, 8 months ago) |
|
|
Does it matter if you use vm&p naptha? or can it just be any naptha.
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: myndreach]
#6948008 - 05/21/07 04:31 PM (16 years, 8 months ago) |
|
|
Im just wondering if anyone knows if it would make a difference.
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: Mr E Guest]
#6957563 - 05/23/07 04:37 PM (16 years, 8 months ago) |
|
|
Aprox how many pulls can you do from 1 batch of mimosa water lye juice
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: enesi]
#6958343 - 05/23/07 07:46 PM (16 years, 8 months ago) |
|
|
I grinded mine
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: darklcd]
#6959399 - 05/23/07 10:54 PM (16 years, 8 months ago) |
|
|
Ok. Done 1 pull but it did not go to well...I think I left the naptha settle for too long after mashing...whats a good time to wait....
Anyways got a little bit, but not as much as expected...and there is this film on the bottom of the pyrex....after i picked the crystals. What is this, its transparent.
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: coAsTal]
#6962552 - 05/24/07 06:24 PM (16 years, 8 months ago) |
|
|
Couple more questions..
what is best way to get naptha off the top to put into evap...we tryed a turkey baster and that worked but not to well as it would not hold in the liquid so we had to tilt it and also it sucks up mimosa juice if you try to get lots in. Is there any faster way to do the naptha into pan to evap?
From what we got off our first pull I just tryed a little to make sure it was dmt we were actually creating this fast. I put some ash then about half a normal dose of dmt and then put a small nug on top. I then held lighet above weed and dmt and sucked in that horrid throat burning fun. Had some good acid style visuals for about 5 minutes....so no break through but that was oviously cos of the conditions.
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: F1234K]
#6963818 - 05/24/07 11:21 PM (16 years, 8 months ago) |
|
|
image
MOD EDIT: if your image is very large, don't post it fullsize but link to it, to avoid the thread becoming unreadable on small screens.
Edited by Wiccan_Seeker (06/20/07 09:19 AM)
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: coAsTal]
#6966354 - 05/25/07 04:26 PM (16 years, 8 months ago) |
|
|
I invented a new tek yesterday, Its called the blow and baste. After mashing naptha in and waiting about 1 and 1/2 hours i went to check on it and noticed that if i blew on the liquid the white merky dmt came up to the surface, so when i removed the naptha for evap i blew then basted and got a big pull.
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: xFrockx]
#7069900 - 06/20/07 01:41 PM (16 years, 7 months ago) |
|
|
Chazz. I did over 5 extractions over a 2 week period with the sludge...its fine...saran it..
-------------------- Im Not Living, Im Just Killing Time
|
F1234K
Wizard Of Tryptamines



Registered: 10/14/06
Posts: 1,241
Last seen: 11 years, 11 months
|
Re: DMT extraction...rootbark to smokeable in roughly 3-4 hours...no grinding, powdering, freezing, [Re: Chazzersize]
#7091306 - 06/25/07 03:43 PM (16 years, 7 months ago) |
|
|
Remeber to wear a mask when adding lye..my friend found out the hard way.
-------------------- Im Not Living, Im Just Killing Time
|
|