Home | Community | Message Board

Shroom Supply
Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

North Spore Shop: Injection Grain Bag

Jump to first unread post Pages: 1
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
InvisibleRedeyedElf
enthusiast
Registered: 10/30/01
Posts: 245
Injecting water?
    #604613 - 04/10/02 08:11 PM (19 years, 9 months ago)

How long should the water be boiled? should a top be kept on the water after boiling while it cools? How many CC's would you recommend inject?

This will be done after a first flush

Should all aborts be picked first??


--------------------
When the walls quit melting, I'll think of a sig


Extras: Filter Print Post Remind Me! Notify Moderator Top
InvisibleRedeyedElf
enthusiast
Registered: 10/30/01
Posts: 245
Re: Injecting water? [Re: RedeyedElf]
    #604853 - 04/11/02 01:07 AM (19 years, 9 months ago)

bump


--------------------
When the walls quit melting, I'll think of a sig


Extras: Filter Print Post Remind Me! Notify Moderator Top
Offlinesixpac440
Psycho Dad
Registered: 01/22/02
Posts: 201
Loc: Michigan
Last seen: 19 years, 3 months
Re: Injecting water? [Re: RedeyedElf]
    #604904 - 04/11/02 02:25 AM (19 years, 9 months ago)

I tried just injecting with a syringe but it would get clogged easily. During injection it would usually blow out of the cake somewhere. So I drilled 2, 3/8 holes in the cake with a 3/8 drill and bit. I alcoholed and flamed the bit first. I cleaned the bit off and re-alcoholed and flamed the bit between cakes. The holes go 3/4 of the way down the cakes. This makes a nice hole to inject the water in. This is much like the reservoir Tek used during jar prep. To see the results of this click on my avatar.

To answer your question directly this is what I do.
I get a new Dixie cup, pour some bottled water in it, draw it into the syringe, fill the holes in the cakes, empty the syringe, spray it with LYSOL, spray the needle shield with LYSOL, put the needle shield on the syringe, put the syringe in a zip-loc baggie, spray the inside of the baggie with LYSOL and seal it up till next time. I water once daily.

The cake should be cleared and could be dunked between flushes.

Hope this helps.


--------------------
Peace
Six


Extras: Filter Print Post Remind Me! Notify Moderator Top
Jump to top Pages: 1

North Spore Shop: Injection Grain Bag


Similar ThreadsPosterViewsRepliesLast post
* To much Alcohol..... SirTripAlot 359 4 09/13/05 10:09 AM
by SirTripAlot
* v.low risk syringe injection technique. doktor_alternate 1,322 8 11/26/03 06:35 AM
by YesItsMe
* Self healing inject points for jars Peterthinks 905 1 11/21/04 03:51 PM
by aussieone
* Questions!!! Alcohol lamps and more satori85 3,842 18 07/09/06 12:44 AM
by satori85
* Tyvek and alcohol? mockeylock 581 2 08/23/05 07:23 PM
by Civ
* Flaming needle inbetween injections..... PROBLEM ganjagoa 1,607 10 12/23/02 08:16 AM
by Alien
* Point of Injection on Spawn Bags Anonymous 1,213 3 02/20/03 12:11 AM
by blackout
* does alcohol kill spores jalfonso 9,115 15 08/21/02 11:33 AM
by Anonymous

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, FooMan, mushboy, fahtster, LogicaL Chaos, 13shrooms, stonesun, wildernessjunkie, cronicr, Pastywhyte, bodhisatta, Tormato
886 topic views. 20 members, 113 guests and 52 web crawlers are browsing this forum.
[ Print Topic | ]
Search this thread:

Copyright 1997-2022 Mind Media. Some rights reserved.

Generated in 0.042 seconds spending 0.018 seconds on 18 queries.