Home | Community | Message Board


Zamnesia.com
Please support our sponsors.

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Amazon Shop for: Microscope

Jump to first unread post. Pages: 1
OfflineAhronZombi
AhronZombi

Registered: 04/06/04
Posts: 1,265
Loc: NY
Last seen: 2 years, 6 months
first print/sysringe
    #2867851 - 07/08/04 07:35 AM (12 years, 5 months ago)

hey yo. im makeing my first syringe from prints. how do i make a print i know the basics but how many caps does it take to make a syringe. i have 2 caps right now in printing enviroments. also how long should i wait to let the spores all drop


--------------------
[url=http://kratom.tcotu.net Low Priced, High Quality Kratom[/url]


Post Extras: Print Post  Remind Me! Notify Moderator
Offlinedoc34
Fungitarian
Male User Gallery

Registered: 02/14/04
Posts: 2,659
Loc: Myceliaville !!!
Last seen: 1 month, 20 days
Re: first print/sysringe [Re: AhronZombi]
    #2867856 - 07/08/04 07:38 AM (12 years, 5 months ago)

try using the FAQ


--------------------


Post Extras: Print Post  Remind Me! Notify Moderator
OfflinepsilocyberV
old hand

Registered: 06/09/99
Posts: 1,809
Last seen: 1 month, 2 days
Re: first print/sysringe [Re: AhronZombi]
    #2867859 - 07/08/04 07:40 AM (12 years, 5 months ago)

Usually you only need a portion of a print from a single mushroom cap to create one spore filled syringe. This depends on the size and density of the deposit, just remember that spores are microscopic and only visible when they are clumped together by the thousands (so just think about how many are actually in a print...).

The cap should be allowed to print for at least 24 hours. Sometimes, with good depositors, you can actaully "move" the mushroom cap to a new surface after only 10-12 hours to get multiple prints from the same cap. Just make sure your cap stays covered during printing with something like a bowl or cup, ect.

If you need a good syringe making guide from print to perform microscopy at home, check out: www.sporeworks.com/syringetek.html


Post Extras: Print Post  Remind Me! Notify Moderator
Jump to top. Pages: 1

Amazon Shop for: Microscope

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Similar ThreadsPosterViewsRepliesLast post
* Spore Prints Posted to Australia justartin 22,054 17 07/13/13 08:46 PM
by FooMan
* Spore prints /w Card Stock question... need to throw in oven? spank0r 750 6 06/08/05 10:02 AM
by Shdwstr
* microscope needs spores cheesie 489 2 01/17/07 03:18 PM
by Roadkill
* How many spores from print needed for LC? GetHyphae 446 8 01/20/09 03:44 PM
by shroober
* Microscope, agar isolation, "print cleaning", tampanensis, flow hoods ADoobie 900 5 11/29/05 06:48 PM
by bongtoke
* Too lite print whodi 641 11 06/26/03 04:46 PM
by Ainasko
* What to look @ under the Microscope? djsollest 982 6 02/05/08 06:13 PM
by stubborn
* Print to Syringe Formula - Mulitspore Theory? BeautifulDay 562 1 04/05/02 11:24 PM
by Zen Peddler

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Magash, Shroomism, george castanza, Prisoner#1, RogerRabbit, Citric, total, FooMan, 13shrooms, stonesun, EvilMushroom666, cronicr, PussyFart
532 topic views. 16 members, 44 guests and 28 web crawlers are browsing this forum.
[ Toggle Favorite | Print Topic | Stats ]
Search this thread:
Shroom Supply
Please support our sponsors.

Copyright 1997-2016 Mind Media. Some rights reserved.

Generated in 0.03 seconds spending 0.005 seconds on 14 queries.