Home | Community | Message Board


This site includes paid links. Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

PhytoExtractum Shop: Buy Bali Kratom Powder

Jump to first unread post Pages: 1
Invisiblemaxmush
Always learning...

Registered: 06/13/20
Posts: 440
Flowhood help (been at this for a while)
    #26916217 - 09/03/20 07:02 PM (3 years, 4 months ago)

Hello all,

Need your help :smile:

We are looking for an interim solution until our industrial flowhood arrives in a couple of months.

I have been searching high and low for a HEPA/blower combo in Canada and its more of a challenge than anticipated. Matching the filter SP to the blower CFM isnt as easy as it sounds.

We are looking for a 24"x 48" filter with minimal depth and a matching blower. It seems we have to look outside of Canada which is fine.

Can anyone help with a current set up that is readily available (preferably in Canada, but US is ok)?

Thanks a bunch!!!


--------------------
Disclaimer: all information presented is intended for educational purposes only. All photos are only representations and not directly from the user.


Extras: Filter Print Post Top
InvisibleFunky Monkey
Human Suppository
 User Gallery

Registered: 05/14/19
Posts: 1,099
Loc: In your MOM's poop shoot
Re: Flowhood help (been at this for a while) [Re: maxmush]
    #26916246 - 09/03/20 07:25 PM (3 years, 4 months ago)

I just sourced stuff for an american build I am doing this week.

This is the blower I just received to go along with this 24 x 48" filter.


Extras: Filter Print Post Top
Invisiblemaxmush
Always learning...

Registered: 06/13/20
Posts: 440
Re: Flowhood help (been at this for a while) [Re: Funky Monkey]
    #26916340 - 09/03/20 08:26 PM (3 years, 4 months ago)

Thanks Funky Monkey. We have that supplier here too. I actually looked at that combo but the SP on the filter is 1.5 and the blower is 1.25. Will this work?


--------------------
Disclaimer: all information presented is intended for educational purposes only. All photos are only representations and not directly from the user.


Extras: Filter Print Post Top
InvisibleFunky Monkey
Human Suppository
 User Gallery

Registered: 05/14/19
Posts: 1,099
Loc: In your MOM's poop shoot
Re: Flowhood help (been at this for a while) [Re: maxmush]
    #26916492 - 09/03/20 09:53 PM (3 years, 4 months ago)

I contacted the manufacturer directly, it's a SP of 1.0.

As for the blower it is a variable speed and has four settings and it has more than enough juice to get 800 cfm for the size of the filter pretty easily even at one of the lowest settings. I feel it's better to have a little too much blower than barely enough, keep the workload easy for the blowers life span, and I can crank it a little higher to scrub the air of my clean room faster/better if I feel the need and then I can set it back down to the speed for laminar flow 🙃


Extras: Filter Print Post Top
Offlinedothedew69
Relearning
 User Gallery


Registered: 08/27/08
Posts: 624
Last seen: 3 years, 2 months
Re: Flowhood help (been at this for a while) [Re: Funky Monkey]
    #26916551 - 09/03/20 10:38 PM (3 years, 4 months ago)

https://www.grainger.com/mobile/product/FANTECH-Galvanized-Steel-Inline-Centrifugal-6XZ77?breadcrumbCatId=3587&fc=MWP2IDP2PCP - this one is pretty strong but may be a tad big, will be good with two high MERV pre-filters. I’ve seen some flowhood cabinets with inline fans, I was considering one of these. But your best bet is American companies. Also check out www.spycor.com and email them, or call, and see if they can get a Glasfloss filter. That’s what I did and they put it up on the site for me to buy. The Glasfloss was much less expensive vs Koch, and the customer service at Koch sucks ass. You can get a metal frame for close to the same cost but I bet you can get wood if desired: https://www.spycor.com/99-99-HEPA-Filter-Metal-Frame-24-x-48-x-5-7-8-p/maggb2448a6ax.htm. They have amazing customer service as well, plus Koch told me 5 weeks, Glasfloss 2-4 weeks much better. Also that filter starts at 0.79 wg unless you go high capacity. Call them and double check or can check data sheets on Glasfloss website. Also you can check www.zoro.com they carry a lot of the same blowers but sometimes at a lower cost. I had mine shipped in a few days.


Extras: Filter Print Post Top
Invisiblemaxmush
Always learning...

Registered: 06/13/20
Posts: 440
Re: Flowhood help (been at this for a while) [Re: dothedew69]
    #26917244 - 09/04/20 11:01 AM (3 years, 4 months ago)

Thanks guys. Helps a lot.

dothedew69, what blower did you end up matching to the Glasfloss filter?


--------------------
Disclaimer: all information presented is intended for educational purposes only. All photos are only representations and not directly from the user.


Edited by maxmush (09/04/20 11:16 AM)


Extras: Filter Print Post Top
Offlinedothedew69
Relearning
 User Gallery


Registered: 08/27/08
Posts: 624
Last seen: 3 years, 2 months
Re: Flowhood help (been at this for a while) [Re: maxmush]
    #26917380 - 09/04/20 12:34 PM (3 years, 4 months ago)

I ended up with a Dayton 1TDT8 but that’s only because I kept with the smaller build, 24x18x6. I was thinking of building something too complex that basically would have been no better than a hepa and pre-filter that’s why I was only looking at the big guys lol. Grainger has amazing customer support, you can call ask for tech support and as long as you have filter data they can tell you if a chosen blower will work. The one guy I had redirected me to a different blower that worked best for me. Good people, definitely give them a call because they may know something we may be missing. I’m frugal but a customer service junkie, good customer service will always get my money. Well my experiences were more exceptional.


Extras: Filter Print Post Top
Invisiblemaxmush
Always learning...

Registered: 06/13/20
Posts: 440
Re: Flowhood help (been at this for a while) [Re: dothedew69]
    #26917425 - 09/04/20 01:10 PM (3 years, 4 months ago)

Thanks. Ill give them a call to see what blower will match that Glasfloss 24 x 48 filter.


--------------------
Disclaimer: all information presented is intended for educational purposes only. All photos are only representations and not directly from the user.


Extras: Filter Print Post Top
Offlinedothedew69
Relearning
 User Gallery


Registered: 08/27/08
Posts: 624
Last seen: 3 years, 2 months
Re: Flowhood help (been at this for a while) [Re: maxmush]
    #26917557 - 09/04/20 02:24 PM (3 years, 4 months ago)

Not a problem and good luck! I did a ton of searching before my purchase and a lot of reading, as far as I know those were the best solutions I could come up with.


Extras: Filter Print Post Top
Jump to top Pages: 1

PhytoExtractum Shop: Buy Bali Kratom Powder


Similar ThreadsPosterViewsRepliesLast post
* Flowhood Questions- Matching filters and blowers ShroomNoob03 1,718 3 06/03/06 03:57 AM
by Brainiac
* Flowhood without hepa filter? TheShroomHermit 1,211 3 04/05/03 12:15 AM
by SixTango
* flowhood, wood framed filter a prob? kilgore_trout 950 4 09/12/04 02:27 PM
by kilgore_trout
* which blower must i use for this hepa filter? yoko 1,511 4 10/22/03 08:11 AM
by dastats
* Tyvek vs Filter Disks?
( 1 2 all )
newmodel 7,631 21 10/25/13 07:41 PM
by TheSacrednessOfGeo
* Need a good HEPA filter... krill 2,901 17 04/01/07 01:56 PM
by flushme
* HEPA Filters- Particle Board vs. Metal Frame ShroomNoob03 1,016 4 01/24/11 07:02 PM
by RiverFish
* Flowhood box MushroomMarkk 1,436 7 05/28/05 03:49 PM
by MushroomMarkk

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a
363 topic views. 39 members, 199 guests and 37 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:

Copyright 1997-2024 Mind Media. Some rights reserved.

Generated in 0.023 seconds spending 0.01 seconds on 14 queries.