|
Shroomboobs
Newbie

Registered: 09/24/19
Posts: 82
Last seen: 3 years, 6 months
|
UnBODified question about PE
#26819982 - 07/12/20 06:26 PM (3 years, 7 months ago) |
|
|
Hello all!
I have been using bods Unmodified tubs and was hoping for a little help with me PE tub. Just going to dive right in.
It’s a new room and haven’t been able to dial in my FAE from my fans and Ac. With things hotter than the devils taint where I live, my ac has been working overtime, unexpectedly increasing my FAE. I leave my lids closed all the way up to pinning until I flip them except when too much condensation causes pooling in the bottom. I then will flip the lid, or crack it, late in colonization periodically to control the excess moisture while still keeping the best possible surface conditions. This time I had a little issue. I had too much FAE an it dried my tubs out a bit and preemptively triggered pinning. My pinset and fruiting is spotty at best. Except for my PE tub.
I got lucky with my PE tub and it seems salvageable. My pins are slowly developing, and there have only been a few side fruits that occurred in the microclimates when it dried out too much. I have since kept the lid closed to fill out my pinset and have begun to see primordial growth. I have also turned my dan off and am relying on the AC to move air for FAE. My question IS how does this tub look to you? I just need some trusted experienced eyes on it. I was sure the surface wasn’t going to pin but it looks like it’s pushing through. I am flipping my lid today to try and cue these little guys and wanted to see what you think. Thank you in advance!
PS- I run these in conjunction to a MMJ grow. They share a 24k ac running on dehumidifier mode. I’m just wondering the best way to have them co exist is and if maybe I need to switch to a more dialed in tub to control the humidity in the tubs.
|
Bsdgaou

Registered: 02/20/19
Posts: 340
|
Re: UnBODified question about PE [Re: Shroomboobs]
#26820348 - 07/13/20 12:39 AM (3 years, 7 months ago) |
|
|
I don't know, look like a trich or like a knots. Wait few days and you'll see.
|
SlugWorthx1


Registered: 03/16/20
Posts: 219
|
Re: UnBODified question about PE [Re: Bsdgaou]
#26820462 - 07/13/20 04:53 AM (3 years, 7 months ago) |
|
|
I agree, looks like mold to me. the knots should be white, whereas in the picture it appears to be gray.
|
rickyswamps
Bad Apple



Registered: 11/08/18
Posts: 1,192
|
Re: UnBODified question about PE [Re: SlugWorthx1]
#26820474 - 07/13/20 05:07 AM (3 years, 7 months ago) |
|
|
Looks ok I think. Hard to tell. Usually folks use a casing layer because PE will blob and put out mutants uncased.
|
A.k.a
Stranger



Registered: 10/27/19
Posts: 16,816
Loc: Gaming the system
Last seen: 1 day, 1 hour
|
Re: UnBODified question about PE [Re: rickyswamps]
#26820600 - 07/13/20 07:36 AM (3 years, 7 months ago) |
|
|
^^^ yep.
PE likes to make these weird shells over the surface sometimes with brownish tissue.
It actually looks pretty good for no casing. A couple blobs but nothing crazy.
If you’re having trouble with stuff drying out you could still sprinkle a late casing on it to help.
--------------------
LAGM2020     
Edited by A.k.a (07/13/20 07:37 AM)
|
Shroomboobs
Newbie

Registered: 09/24/19
Posts: 82
Last seen: 3 years, 6 months
|
Re: UnBODified question about PE [Re: A.k.a]
#26857824 - 08/01/20 08:43 PM (3 years, 6 months ago) |
|
|
Thanks for the tips! I actually was planning on using more bulk substrate on top to try a psuedo casing this next run
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 191 topic views. 41 members, 157 guests and 39 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|