Home | Community | Message Board

Magic Mushrooms Zamnesia
This site includes paid links. Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

PhytoExtractum Shop: Maeng Da Thai Kratom Leaf Powder

Jump to first unread post Pages: 1
OfflineSugabearcrisp
Not Your Average Bear
Male User Gallery


Registered: 10/14/19
Posts: 12,047
Loc: maybe I had too much, too fast
Last seen: 3 hours, 35 minutes
Re: DIY Pro-Tips/Life Hacks [Re: LogicaL Chaos] * 2
    #27044088 - 11/17/20 03:48 PM (3 years, 2 months ago)

When pulling nails out of drywall use a wide spatula or similar item to spread the pressure from the hammer and prevent a hole in the drywall. Also works well for prying off trim without damaging the wall




If you break the head off a nail that you are trying to pull out use a pair of vice grips to clamp on and then use the rounded part of the grips like a lever to pull the nail out



Going to try to keep adding tips like this if you guys think they are helpfil


--------------------
Indirect Weighing tek


Extras: Unfilter Print Post Top
OfflineSugabearcrisp
Not Your Average Bear
Male User Gallery


Registered: 10/14/19
Posts: 12,047
Loc: maybe I had too much, too fast
Last seen: 3 hours, 35 minutes
Re: DIY Pro-Tips/Life Hacks [Re: LogicaL Chaos] * 1
    #27056950 - 11/25/20 10:55 AM (3 years, 2 months ago)

Coping is an essential part of installing baseboard molding. If you do two 45 degree angles the tendency is for them to separate over time, especially during dry winter. Instead you pick the longest section that is first seen when you walk into a room, install a piece with flat ends and then cope the pieces that abutt to it so they fit over the molding. This is how I do it

1. Cut at 45 degrees across the face of your molding


2. This gives an outline of the molding



3.clamp it on a workbench



4. Use a coping saw to cut along the edge


5. Finish up with a sharp utility knife, a file or rasp can also be used



Once done the piece will now fit over another piece of the same molding perfectly.


(Straight piece on left and coped piece on right)


--------------------
Indirect Weighing tek


Edited by Sugabearcrisp (11/25/20 11:55 AM)


Extras: Unfilter Print Post Top
OfflineSugabearcrisp
Not Your Average Bear
Male User Gallery


Registered: 10/14/19
Posts: 12,047
Loc: maybe I had too much, too fast
Last seen: 3 hours, 35 minutes
Re: DIY Pro-Tips/Life Hacks [Re: Renoraines] * 2
    #28216257 - 03/05/23 05:32 PM (10 months, 18 days ago)

Great tip for using a magnet to find screws when you don't have a stud finder :thumbup:

I can even see that being very helpful if you need to take down some dry wall.


Extras: Unfilter Print Post Top
Jump to top Pages: 1

PhytoExtractum Shop: Maeng Da Thai Kratom Leaf Powder


Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Ythan, Anno, Thor, Link, Seuss
3,979 topic views. 0 members, 0 guests and 0 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:

Copyright 1997-2024 Mind Media. Some rights reserved.

Generated in 0.021 seconds spending 0.007 seconds on 17 queries.