|
MushkingMulah360
Amateur Mycologist

Registered: 01/13/20
Posts: 184
Loc:
Last seen: 3 years, 8 months
|
SAB Build w/pics ...input on gloves much needed!!!
#26446432 - 01/22/20 01:45 PM (4 years, 7 days ago) |
|
|
Ok so I bought a 110 L clear sterilite latching tub along with 2 pvc flanges (found lids to screw into it right next to it on another piece of pvc) plus silicone to seal everything and a pair of the longest and most durable gloves I could find in Home Depot and a few other stores. Unfortunately after getting them home I’m feeling they’re just not long enough for my liking especially after I attach them to the pvc it’s going to limit my range of motion a lot. I would like to find a pair that are atleast twice as long and extremely durable so I can have the widest range of motion possible. What did everyone else use? or any other ideas would be greatly appreciated. Thanks in advance!!! 

|
cronicr



Registered: 08/07/11
Posts: 61,436
Loc: Van Isle
Last seen: 2 years, 8 days
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: MushkingMulah360]
#26446433 - 01/22/20 01:47 PM (4 years, 7 days ago) |
|
|
Detach the gloves you don't need or want them
--------------------
  It doesn't matter what i think of you...all that matters is clean spawn I'm tired do me a favor
|
cronicr



Registered: 08/07/11
Posts: 61,436
Loc: Van Isle
Last seen: 2 years, 8 days
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: cronicr]
#26446437 - 01/22/20 01:49 PM (4 years, 7 days ago) |
|
|
 A box...two arm holes...done
--------------------
  It doesn't matter what i think of you...all that matters is clean spawn I'm tired do me a favor
|
MushkingMulah360
Amateur Mycologist

Registered: 01/13/20
Posts: 184
Loc:
Last seen: 3 years, 8 months
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: cronicr]
#26446438 - 01/22/20 01:51 PM (4 years, 7 days ago) |
|
|
That was my next question, if it’s not going to up the chance of contamination’s much without them I guess I could do with out right? I just want it to be as contam free as possible!!!
|
MycoStu

Registered: 08/10/19
Posts: 168
Loc: USA
Last seen: 3 years, 4 months
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: cronicr]
#26446439 - 01/22/20 01:52 PM (4 years, 7 days ago) |
|
|
Quote:
cronicr said: Detach the gloves you don't need or want them
The gloves inside the box will create wind and kick up any baddies that are hanging around within. Just make sure your hands are surgically clean before going in and make as little wind as possible.
https://www.shroomery.org/forums/showflat.php/Number/23990888#23990888 SAB Tek
Edited by MycoStu (01/22/20 01:53 PM)
|
MushkingMulah360
Amateur Mycologist

Registered: 01/13/20
Posts: 184
Loc:
Last seen: 3 years, 8 months
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: cronicr]
#26446440 - 01/22/20 01:53 PM (4 years, 7 days ago) |
|
|
Thanks for the quick response want to finish this up and haven’t because of the gloves!!!!
|
cronicr



Registered: 08/07/11
Posts: 61,436
Loc: Van Isle
Last seen: 2 years, 8 days
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: MushkingMulah360]
#26446442 - 01/22/20 01:54 PM (4 years, 7 days ago) |
|
|
I don't use gloves at all, your hands don't go over your work anyway just wash them before you sit down
--------------------
  It doesn't matter what i think of you...all that matters is clean spawn I'm tired do me a favor
|
MushkingMulah360
Amateur Mycologist

Registered: 01/13/20
Posts: 184
Loc:
Last seen: 3 years, 8 months
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: cronicr]
#26446445 - 01/22/20 01:56 PM (4 years, 7 days ago) |
|
|
I strive to one day be half as good as you Cron so I take your word the gloves aren’t needed!!! Thanks man
|
Psilotyl
נָזִיר


Registered: 08/30/19
Posts: 469
Loc: עולם
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: MushkingMulah360]
#26446450 - 01/22/20 02:02 PM (4 years, 7 days ago) |
|
|
I don’t have attached gloves either and I don’t have any problems. I just makes sure I’m clean and wear nitrate gloves when I work. I imagine if they were attached it would greatly restrict my ability of movement and to work. Just be clean and disinfect from elbows down with 80% isopropyl alcohol before working and you’ll be fine.
--------------------
שלום וְאור | PEACE & LIGHT
|
footpath
ὕδωρχοίρος

Registered: 07/16/19
Posts: 1,367
Last seen: 1 year, 2 months
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: Psilotyl]
#26446456 - 01/22/20 02:08 PM (4 years, 7 days ago) |
|
|
Having gloves creates a positive pressure that agitates the air.
You wanna imagine it like moving your arms in water without causing a wake.
|
Demetrius18
Stranger



Registered: 01/09/20
Posts: 40
Loc: Yes
Last seen: 1 year, 7 months
|
Re: SAB Build w/pics ...input on gloves much needed!!! [Re: MushkingMulah360]
#26446457 - 01/22/20 02:08 PM (4 years, 7 days ago) |
|
|
Lol I was almost going through that last week but looking at the work area, the actual work and the time, I was done faster than I sanitized the box, theoretically if you wash your hands then alcohol sterilize, other than maybe dry skin nothing should fall from hands but there is still so much room, unless you're cramped doing 10 plates its negligible.
-------------------- This account is purely theoretical, I will be king of the pirates!
|
|