Home | Community | Message Board

World Seed Supply
Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Shop: Kraken Kratom Red Vein Kratom   Unfolding Nature Unfolding Nature: Being in the Implicate Order

Jump to first unread post Pages: 1
OfflineGadget
addict

Registered: 11/17/99
Posts: 341
Last seen: 20 years, 6 months
Re: Make your own printed cuircut boards
    #258880 - 05/06/00 04:22 AM (22 years, 5 months ago)

Funny, I Just did this about a month ago. I had built a new center channel speaker using 2 shieled 6 1/2" Poly cones and a Shieled 1" tweet.

I used a 3rd order low pass filter for the mid-bass and a 3rd order High pass for the tweet. When I first built it I just hand wired it, but what a nightmare, so I went to radio shack and picked up the materials to etch my own board, It looked SOO much nicer (even thought no one but me will ever see it :wink: )

Its good to see I'm not the only crazy person here....

/Gadget



Extras: Filter Print Post Top
Offlineoneoverzero
veteran
Registered: 01/24/00
Posts: 758
Loc: Cyber Space
Last seen: 20 years, 9 months
Re: Make your own printed cuircut boards [Re: Gadget]
    #258882 - 05/08/00 10:42 AM (22 years, 4 months ago)

Hey Gadget, that's kewl!

Where did you get the design for two third order x-overs? That's some serious frequency pass antentuation!



--------------------
[red]0011 0001 0010 1111 0011 0000[/red]


Extras: Filter Print Post Top
OfflineGadget
addict

Registered: 11/17/99
Posts: 341
Last seen: 20 years, 6 months
Re: Make your own printed cuircut boards [Re: Gadget]
    #258883 - 05/08/00 04:54 PM (22 years, 4 months ago)

For the x-overs design I went to: http://kbapps.com its under the enclosure calculators section.

I used Speaker Workshop (free) from http://audua.com to chart driver impediance and phase. Its a NEAT little program! Also the app was really helpfull during x-over design because I could readily see the results in a chart

I haven't done a freq responce yet (well I did a few in room, but the look like crap) I am getting my hands on a laptop so I can take the enclosure outdoors to a huge parking lot and do freq responce without getting all the reflections included.

Here are the impediance charts for the raw drivers.

So fr its been a Very enjoyable project :wink:



Extras: Filter Print Post Top
Jump to top Pages: 1

Shop: Kraken Kratom Red Vein Kratom   Unfolding Nature Unfolding Nature: Being in the Implicate Order


Similar ThreadsPosterViewsRepliesLast post
* Inspector Gadget Trine 724 2 07/24/01 10:32 AM
by batou
* Fad Gadget looner2 479 1 04/04/05 05:55 AM
by looner2
* Is it ok to plug a guitar into pricey PC speakers? RedNucleus 651 1 06/19/04 02:41 AM
by Rob_K
* more music boards? yelimS 741 4 11/10/03 12:15 AM
by orizon
* Music like Boards of Canada
( 1 2 all )
Redstorm 3,500 38 09/21/04 01:23 AM
by idiotek
* Boards of Canada - Question for fans. Fliquid 1,019 16 05/06/04 11:15 PM
by Blastrid
* Boards of Canada Fliquid 1,122 12 09/11/02 06:06 AM
by Fliquid
* Since A.H.P. Members almost never visit the board... Fliquid 1,033 12 04/03/03 04:22 PM
by Fliquid

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Middleman, automan, DividedQuantum
1,162 topic views. 0 members, 1 guests and 0 web crawlers are browsing this forum.
[ Show Images Only | Print Topic ]
Search this thread:

Copyright 1997-2022 Mind Media. Some rights reserved.

Generated in 0.021 seconds spending 0.005 seconds on 13 queries.