Home | Community | Message Board

MRCA Tyroler Gluckspilze
Please support our sponsors.

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Amazon Shop: ½ Pint Jars

Jump to first unread post. Pages: 1
Registered: 03/29/04
Posts: 4
Last seen: 13 years, 10 months
Spore Print Question
    #2573440 - 04/18/04 11:23 AM (13 years, 11 months ago)

Hey all!
I posted up some pics a while ago in regards to a store bought kit I had purchased that ended up getting contaminated. So I turfed it.

Anyhow, Not wanting to give up cultivation, I figured I would follow the TEK and start by making cakes... but here is my problem.

I was given the spore print in a little pill container, Not the usual syringe... how might I go about inoculating the jars without the syringe. I imagine it's just a different method, but I wanted to avoid contamination best as possible.

I don't at all want to give you pros headaches, but any information is appreciated.

Post Extras: Print Post  Remind Me! Notify Moderator
fluid druid
 User Gallery

Registered: 02/10/04
Posts: 15,474
Loc: Zone ate
Re: Spore Print Question [Re: de_mix]
    #2573470 - 04/18/04 11:44 AM (13 years, 11 months ago)

Explane a little more about the container the spores are in?
I have never heard of them being in a "pill container" so unsure.

If there dry, you need to get a shot glass, some distilled water, a
needle and syringe, and a very clean working area, like a glove box.

If there wet you need another method, but I shall assume they are dry for now.

You then need to fill the syringe with distilled water, working inside
the shot glass, you want to get dh2o into the spores to mix in, you want to
do this with the water touching as little else as possible, i.e the outside of the pill casing ext, or not get it on anywere you might have touched.

Then you need to suck the spores + dh2o back into the syringe.

All this needs to be done as clean as possible, and then assuming the print was clean, you should have a spore syringe, then follow your chossen tec.

Post Extras: Print Post  Remind Me! Notify Moderator
Jump to top. Pages: 1

Amazon Shop: ½ Pint Jars

Mushrooms, Mycology and Psychedelics >> Mushroom Cultivation

Similar ThreadsPosterViewsRepliesLast post
* Syringe and Spore Print question HellaJZ 1,408 3 08/09/01 05:44 PM
by L3D
* Spore print question ????? mojowilliams 960 10 01/04/02 12:31 PM
by ar393
* Spore print question Scarface 563 1 11/27/01 08:16 PM
by josh666
* Spore Print Question Deviant 678 2 09/21/01 02:47 PM
by darkfly
* spore printing question phrozendata 512 2 11/05/01 10:46 AM
by phrozendata
* How do you use spore prints efficently? dnkyrhubarb 7,376 10 08/21/16 01:09 PM
by Kenetic
* spore printing / syringe making *DELETED*
( 1 2 all )
phrozendata 3,785 27 03/19/02 06:17 PM
by Roadkill

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Roadkill, Magash, Shroomism, george castanza, RogerRabbit, Citric, total, FooMan, 13shrooms, stonesun, cronicr, PussyFart, Tmethyl, Pastywhyte, bodhisatta
391 topic views. 27 members, 126 guests and 17 web crawlers are browsing this forum.
[ Toggle Favorite | Print Topic | Stats ]
Search this thread:
Please support our sponsors.

Copyright 1997-2018 Mind Media. Some rights reserved.

Generated in 0.188 seconds spending 0.127 seconds on 31 queries and 0.034 seconds on Sphinx.