|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
rabidgod
Salonky

Registered: 09/04/18
Posts: 5
Last seen: 5 years, 5 months
|
1st Tub, any advice is welcome
#25628272 - 11/20/18 05:13 PM (6 years, 1 month ago) |
|
|
Used grain bags inoculated with pes Hawaiian , coir Verm 50/50 tek. Put into fruiting on 11/10. What’s the average time to see pins, roughly.[image align=left]http://https://ibb.co/gbMKkV https://ibb.co/j39iCA https://ibb.co/k2xyeq https://ibb.co/by7LsA https://ibb.co/ntbrzq https://ibb.co/dibrzq https://ibb.co/b7v6XA[/image]
|
rabidgod
Salonky

Registered: 09/04/18
Posts: 5
Last seen: 5 years, 5 months
|
Re: 1st Tub, any advice is welcome [Re: rabidgod]
#25628277 - 11/20/18 05:15 PM (6 years, 1 month ago) |
|
|
I cut the tape, i found out after i was in a couple days that it wasn’t supposed to be there. It’s shrinking properly
|
johney89
Duck


Registered: 04/10/17
Posts: 103
Last seen: 7 months, 26 days
|
Re: 1st Tub, any advice is welcome [Re: rabidgod]
#25628341 - 11/20/18 05:53 PM (6 years, 1 month ago) |
|
|
not sure what you mean by the tape and shrinking. I didnt use a liner on either grow that i have done and all have been fine.
As for pins, be patient, they will come. All of mine have went more than 10 days for sure before any pins. Nothing else really to say here other than rock and and get ready.
I have a penis envy tub going right now that i still have no pins in. It was put into fruiting conditions 11/26
|
rabidgod
Salonky

Registered: 09/04/18
Posts: 5
Last seen: 5 years, 5 months
|
Re: 1st Tub, any advice is welcome [Re: johney89]
#25630500 - 11/21/18 04:44 PM (6 years, 1 month ago) |
|
|
i think mainly what i was looking for is, does the mic look ok?
noob questions: are the knots future pins? theres one corner that just doesnt have any, should i be worried? if i see surface moisture, does that mean the tub is still humid enough, even if the walls arent moist? whats the proper amount of polyfill to use? i think i used too much
|
Sparky101
Electrical Guru


Registered: 02/14/18
Posts: 168
Loc: Midwest
Last seen: 2 months, 4 days
|
Re: 1st Tub, any advice is welcome [Re: rabidgod]
#25630770 - 11/21/18 06:18 PM (6 years, 1 month ago) |
|
|
Quote:
rabidgod said: i think mainly what i was looking for is, does the mic look ok?
noob questions: are the knots future pins? theres one corner that just doesnt have any, should i be worried? if i see surface moisture, does that mean the tub is still humid enough, even if the walls arent moist? whats the proper amount of polyfill to use? i think i used too much
Looks great to me! Yes I believe knots are typically future pins and the more the merrier. Don’t be worried about the corner, the substrate wasn’t completely level I’d guess. I don’t worry about the walls being damp, just the substrate surface because that’s the most important. If you have small water beads on the surface that’s good, just fan a couple times a day and only mist if the droplets evaporate.
I couldn’t tell you about the poly, I use Unmodified tubs however more fresh air is needed at this point by the looks of it.
Just keep doing what you’re doing, lookin good!
-------------------- Never ask someone to do something that you wouldn’t do yourself.
|
rabidgod
Salonky

Registered: 09/04/18
Posts: 5
Last seen: 5 years, 5 months
|
Re: 1st Tub, any advice is welcome [Re: Sparky101]
#25630795 - 11/21/18 06:34 PM (6 years, 1 month ago) |
|
|
Gracias, yea i fan when i wake up and when i get home from work. I’m gone most of the day. I took my poly down to what fills the hole, i had it hella stuffed.
|
Sparky101
Electrical Guru


Registered: 02/14/18
Posts: 168
Loc: Midwest
Last seen: 2 months, 4 days
|
Re: 1st Tub, any advice is welcome [Re: rabidgod]
#25630875 - 11/21/18 07:12 PM (6 years, 1 month ago) |
|
|
Quote:
rabidgod said: Gracias, yea i fan when i wake up and when i get home from work. I’m gone most of the day. I took my poly down to what fills the hole, i had it hella stuffed.
I do the same man. I’ve found that the less I fuck around with my tubs the better they do. I’m on my 7th mono with cubes and used only bods teks. My most recent one just pinned last night at day 9, by the looks of yours you should have pins by the end of the weekend.
-------------------- Never ask someone to do something that you wouldn’t do yourself.
|
rabidgod
Salonky

Registered: 09/04/18
Posts: 5
Last seen: 5 years, 5 months
|
Re: 1st Tub, any advice is welcome [Re: Sparky101]
#25633690 - 11/23/18 05:38 AM (6 years, 1 month ago) |
|
|
WE GOT PERNS!!!
Scoped 4 this morning. Phew, was getting worried i muffed em up. Fanning def helped
|
Sparky101
Electrical Guru


Registered: 02/14/18
Posts: 168
Loc: Midwest
Last seen: 2 months, 4 days
|
Re: 1st Tub, any advice is welcome [Re: rabidgod]
#25633759 - 11/23/18 06:54 AM (6 years, 1 month ago) |
|
|
-------------------- Never ask someone to do something that you wouldn’t do yourself.
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, hamloaf, cronicr, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 294 topic views. 30 members, 99 guests and 29 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|