|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
frankwhite85
Stranger


Registered: 04/18/16
Posts: 305
Last seen: 1 month, 6 days
|
jagged edges in holes in jar lids
#23848788 - 11/19/16 02:06 PM (7 years, 2 months ago) |
|
|
When i make my holes in my jar lids i file down the jagged edges pretty well but I was just curious what the real concern was? Is it not good to have it touching the sfd or is it more problematic because it can cut up the grain when shaken?
|
enlightenment
alchemist


Registered: 08/09/09
Posts: 1,647
Loc: Europe
Last seen: 8 months, 21 days
|
Re: jagged edges in holes in jar lids [Re: frankwhite85]
#23848804 - 11/19/16 02:11 PM (7 years, 2 months ago) |
|
|
I hate edgy holes. They start to rust after some time.
Cutting up grain would not be a problem and it never happened to me.
I think I already posted this thread to you in another thread but if others have the same issue with edgy holes it might be helpful.
|
mrmazdarx9
Pffffttt


Registered: 05/15/16
Posts: 9,796
Loc: behind you
Last seen: 1 year, 4 months
|
Re: jagged edges in holes in jar lids [Re: enlightenment]
#23848830 - 11/19/16 02:20 PM (7 years, 2 months ago) |
|
|
Quote:
enlightenment said: I hate edgy holes. They start to rust after some time.
Cutting up grain would not be a problem and it never happened to me.
I think I already posted this thread to you in another thread but if others have the same issue with edgy holes it might be helpful.
I heard you like smooth holes
-------------------- COCA GROWERS come here and share your knowledge COCA GROWERS UNITE
Click here for UK trades
need some supplies in the UK check Here or PM me UK OTD uk members chat UK supplies and trade OTD place to chat shit Right Here If you use "SWIM" you should DROWN
|
Kenetic
Nam Sayin



Registered: 08/24/14
Posts: 4,389
Loc: I don't believe in land
Last seen: 5 years, 3 months
|
Re: jagged edges in holes in jar lids [Re: frankwhite85]
#23848983 - 11/19/16 03:26 PM (7 years, 2 months ago) |
|
|
I heard yours is one of them
Quote:
frankwhite85 said: Is it not good to have it touching the sfd or is it more problematic because it can cut up the grain when shaken?
Both are scenarios worth taking into consideration. If you drill slowly with light pressure the holes will be clean most of the time. You could clean a punched hole with half of a soda can tab.
-------------------- Todo Cambia    DMT said: Everyone know's me, they just don't know it yet
|
axis_tech
Rollin' Stoned


Registered: 02/27/05
Posts: 294
Last seen: 4 years, 9 months
|
Re: jagged edges in holes in jar lids [Re: Kenetic]
#23849007 - 11/19/16 03:37 PM (7 years, 2 months ago) |
|
|
I have been keeping an eye out for a 3/8" hole punch cause of the burrs after drilling. When I used to punch the holes with a screwdriver I would flip the lid over and use the back side of the screwdriver to level out the stray pieces but like enlightenment said it's prone to rust and annoying to clean.
-------------------- takes a token' and keeps on smoken'
|
mrmazdarx9
Pffffttt


Registered: 05/15/16
Posts: 9,796
Loc: behind you
Last seen: 1 year, 4 months
|
Re: jagged edges in holes in jar lids [Re: Kenetic]
#23849132 - 11/19/16 04:22 PM (7 years, 2 months ago) |
|
|
Quote:
kenetic said: I heard yours is one of them lol.
maybe maybe
-------------------- COCA GROWERS come here and share your knowledge COCA GROWERS UNITE
Click here for UK trades
need some supplies in the UK check Here or PM me UK OTD uk members chat UK supplies and trade OTD place to chat shit Right Here If you use "SWIM" you should DROWN
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 228 topic views. 20 members, 196 guests and 26 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|