|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
modsolution
Stranger


Registered: 07/21/11
Posts: 81
Last seen: 2 years, 10 months
|
Re: Help with flow hood please!! [Re: Boogieman47]
#23824807 - 11/12/16 02:29 AM (7 years, 2 months ago) |
|
|
OK wow now its making more seance. I see how your getting there now. Man thanks for the help. I do have another question though the blower you suggest is more configured for what I need, now that I understand things a lil better. but I can get the 1Tdu2 for $80 cheaper but I would rather spend the $80 than have more trouble than its worth. So will I run into trouble with the 1Tdu2 if i cut down the intake air.
Edited by modsolution (11/12/16 02:42 AM)
|
modsolution
Stranger


Registered: 07/21/11
Posts: 81
Last seen: 2 years, 10 months
|
Re: Help with flow hood please!! [Re: Boogieman47]
#23824812 - 11/12/16 02:32 AM (7 years, 2 months ago) |
|
|
Quote:
noob47 said: That hepa is nuclear grade
LOL hope I don't hurt my self. but I think I already have this has been such a pain. I got it for $40 a couple of years ago but figuring everything out was killing me so I gave up. I couldn't find the answers or someone to explain it well enough. I do appreciate it!!
-------------------- IF YOU'RE NOT LIVING ON THE EDGE YOU'RE TAKING UP TO MUCH SPACE! I THOUGHT I WAS WRONG ONCE BUT I WAS MISTAKEN!!
|
Boogieman47
Let's boogie


Registered: 03/05/16
Posts: 9,712
Loc: Under your bed
|
Re: Help with flow hood please!! [Re: modsolution]
#23824817 - 11/12/16 02:43 AM (7 years, 2 months ago) |
|
|
No its fine its for a clean room at nuke plants i believe ... like i said i have one the same you can always get the bigger one mine is a huge fan i got for free and i bogged it down with a plastic tote ... too be honest i didnt do mine to specs due to not being able to find any on the motor the manufacturer has been outta businesd for 40 years i just started with a small hole and worked it bigger till my flame was bent wity no flicker i was just trying to help you understand the process a bit because it took alot of work on my end to find out what i had to do i basically called the hepas engineer and went over shit with him and rolled with it
|
modsolution
Stranger


Registered: 07/21/11
Posts: 81
Last seen: 2 years, 10 months
|
Re: Help with flow hood please!! [Re: Boogieman47]
#23824822 - 11/12/16 02:51 AM (7 years, 2 months ago) |
|
|
You are awesome dude thanks a million. Now I feel I can go ahead and get this thing made. any suggestions on how to make the box? I think that is preaty straight forward but if you have a suggestion I will take it!! Bye the way Keep up the good work I am sure more people than me appreciate you on here.
-------------------- IF YOU'RE NOT LIVING ON THE EDGE YOU'RE TAKING UP TO MUCH SPACE! I THOUGHT I WAS WRONG ONCE BUT I WAS MISTAKEN!!
|
Boogieman47
Let's boogie


Registered: 03/05/16
Posts: 9,712
Loc: Under your bed
|
Re: Help with flow hood please!! [Re: modsolution]
#23824843 - 11/12/16 03:19 AM (7 years, 2 months ago) |
|
|
Thanks man and i ran 25"x24"top, bottom, cuts on the wood that will give you a half inch off each side giving you a place to drill screws and be flush.... and 24"x24"on the sides ... the back i put a piece of 2x4 to support the fan and enclosed it with a piece of plywood i measured out 11.5 on the inside of the plywood and nailed 1x1" wood strips to the outside of the 11.5 you can even do 11.3/4" makes it so the air goes through and not around your hepa... put either wood glue or caulking down on the hepa and plywood dont forget to measure your hole for your fan and cut that out before doing all that and go from there that will give you 12.5" of plenum well enough space to build up pressure behind your filter
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 493 topic views. 30 members, 229 guests and 54 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|