Home | Community | Message Board


This site includes paid links. Please support our sponsors.


Welcome to the Shroomery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

North Spore Shop: Injection Grain Bag, North Spore Mushroom Grow Kits & Cultivation Supplies

Jump to first unread post Pages: 1
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
OfflineChitihurrishrooms
Entrepreneur
Male
Registered: 02/13/16
Posts: 99
Last seen: 1 year, 6 months
Plastic lid question
    #23669795 - 09/22/16 11:31 PM (7 years, 4 months ago)

Two questions actually.
First I bought plastic lids from Amazon. Put in the injection ports and the filters. After pcing a batch of jars I noticed two things I didn't like on every jar. First every jar kid was a little loose. I gave them all a tighten right away. Is this normal? Is this an issue? Do the original metal rings do that?
Second question I noticed the grains were wetter in random areas in the jars. I think this is normal but I'm not 100% sure. Is this just from the grains being originally wet and will even out after shaking and sitting? Thanks in advance


Extras: Filter Print Post Top
OfflineBobabouy
Shrimp Boat Captain
Male


Registered: 01/19/16
Posts: 661
Loc: The Black Sea
Last seen: 6 years, 16 days
Re: Plastic lid question [Re: Chitihurrishrooms]
    #23669817 - 09/22/16 11:37 PM (7 years, 4 months ago)

The plastic lids expand and it loosens them a tad. Just tighten them after the PC cycle. When the cool enough to handle, shake them to redistribute the moisture. This is all normal.


Extras: Filter Print Post Top
OfflineChitihurrishrooms
Entrepreneur
Male
Registered: 02/13/16
Posts: 99
Last seen: 1 year, 6 months
Re: Plastic lid question [Re: Bobabouy]
    #23669821 - 09/22/16 11:39 PM (7 years, 4 months ago)

Ok cool thanks


Extras: Filter Print Post Top
InvisibleInocuole
Scalpel of Evil's Bane
 User Gallery

Folding@home Statistics
Registered: 11/21/11
Posts: 24,863
Loc: ★
Trusted Cultivator
Re: Plastic lid question [Re: Chitihurrishrooms]
    #23670104 - 09/23/16 05:43 AM (7 years, 4 months ago)

Don't tighten them after the PC cycle... just leave them how they are.  If you tighten them while they're hot they're a mega bitch to get off once they cool, plus you start warping your threads and they just get harder to turn later.  Just pick them straight up and put them somewhere without much draft.  If you must tighten them, only do it just barely.

Better off tightening them BEFORE the PC cycle, then when they're hot they won't be so loose that they're a hazard.


--------------------
                            :rainbowdrink: Tea doesn't work?                            AMU  (Q & A)                  Grain prep for Intergalactic Space Oats :pes:     

Coir-ca-cola
Jokes are funny until they're about you


Extras: Filter Print Post Top
OfflineBobabouy
Shrimp Boat Captain
Male


Registered: 01/19/16
Posts: 661
Loc: The Black Sea
Last seen: 6 years, 16 days
Re: Plastic lid question [Re: Inocuole]
    #23670112 - 09/23/16 05:49 AM (7 years, 4 months ago)

I don't know what kind of plastic lids everyone else is using, but I get mine at Wally World. I tighten the shit out of them when they come out of the pressure cooker and I never have any problems removing them later. But if your scared your lids will get stuck on the jars, then just tighten slightly or not at all. Doesn't really make a difference in the end.


Extras: Filter Print Post Top
InvisibleInocuole
Scalpel of Evil's Bane
 User Gallery

Folding@home Statistics
Registered: 11/21/11
Posts: 24,863
Loc: ★
Trusted Cultivator
Re: Plastic lid question [Re: Inocuole]
    #23670135 - 09/23/16 06:06 AM (7 years, 4 months ago)

Quote:

Bobabouy said:
Doesn't really make a difference in the end.




Except for...

Quote:

Inocuole said:
you start warping your threads and they just get harder to turn later.




Some get so warped the lid will fucking pop right off with barely a twist.  It's not a good time.


Extras: Filter Print Post Top
OfflineBobabouy
Shrimp Boat Captain
Male


Registered: 01/19/16
Posts: 661
Loc: The Black Sea
Last seen: 6 years, 16 days
Re: Plastic lid question [Re: Inocuole]
    #23670167 - 09/23/16 06:32 AM (7 years, 4 months ago)

I see your point but that's not a problem I've run into. I've ran these lids through countless cycles and they still screw on and hold tight just like they did when they were new. And they're the cheap ass Walmart Mainstay brand. The reason I tighten them down good after pc'ing is that they are still a little soft and expanded. When they cool, I know they have shrunk to fit the jar tight. Now that I think about it, I have had a couple that seemed a little "out of round" but after tightening them and pc'ing them the shape seems to come back. Never had to throw one away because it lost function.


Extras: Filter Print Post Top
InvisibleInocuole
Scalpel of Evil's Bane
 User Gallery

Folding@home Statistics
Registered: 11/21/11
Posts: 24,863
Loc: ★
Trusted Cultivator
Re: Plastic lid question [Re: Bobabouy]
    #23670177 - 09/23/16 06:36 AM (7 years, 4 months ago)

I haven't had to throw any away yet either, but I have a few stubborn ones that definitely weren't that way at first.  I imagine this could reduce the effectiveness of the jar overall if it got out of hand.  Just consider it a sneak preview into what might happen if you keep doing it. :shrug:

I also run a bit higher than 15psi so that could be a factor I guess.


--------------------
                            :rainbowdrink: Tea doesn't work?                            AMU  (Q & A)                  Grain prep for Intergalactic Space Oats :pes:     

Coir-ca-cola
Jokes are funny until they're about you


Extras: Filter Print Post Top
OfflineBobabouy
Shrimp Boat Captain
Male


Registered: 01/19/16
Posts: 661
Loc: The Black Sea
Last seen: 6 years, 16 days
Re: Plastic lid question [Re: Inocuole]
    #23670206 - 09/23/16 06:48 AM (7 years, 4 months ago)

Quote:

Inocuole said:
I haven't had to throw any away yet either, but I have a few stubborn ones that definitely weren't that way at first.  I imagine this could reduce the effectiveness of the jar overall if it got out of hand.  Just consider it a sneak preview into what might happen if you keep doing it. :shrug:

I also run a bit higher than 15psi so that could be a factor I guess.



I was going to ask how hot you were getting them. Not sure what kind of plastic they use or at what temp the bonds start to break down. Never was a concern. Now banded lids on the other hand, I usually have to tap the edge of the band on opposite sides to get them to break free. They are all dented up but still keep on truckin.


Extras: Filter Print Post Top
Jump to top Pages: 1

North Spore Shop: Injection Grain Bag, North Spore Mushroom Grow Kits & Cultivation Supplies


Similar ThreadsPosterViewsRepliesLast post
* plastic lids and filter disks-how to use? GaNjAShRooM 3,284 4 03/12/02 03:50 PM
by cookiewhore
* Plastic lid holes, 3/8 or 1/2 inch??
( 1 2 all )
Visigoth 6,262 24 04/12/02 06:02 AM
by cookiewhore
* Plastic lids Daft420 1,771 4 07/24/01 09:01 PM
by Doc
* Easy sterilization w/o plastic lids? Captain_Undeez 1,355 2 04/12/02 10:18 AM
by SixTango
* Re: Source for Plastic Lids? Psychonaut 1,577 5 05/26/00 04:45 PM
by AnubisRonin
* Plastic Lids KitMarlowe 1,077 5 12/30/01 09:53 AM
by Anonymous
* plastic lids??? I_and_I 861 2 07/22/02 06:47 PM
by dracon
* plastic lids safe? dalorean 894 2 06/16/02 05:34 PM
by SixTango

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a
210 topic views. 13 members, 150 guests and 24 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:

Copyright 1997-2024 Mind Media. Some rights reserved.

Generated in 0.025 seconds spending 0.01 seconds on 14 queries.