|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
burgerguy
Stranger


Registered: 08/04/14
Posts: 56
Last seen: 7 years, 11 months
|
large injection sites
#21581304 - 04/22/15 06:05 PM (9 years, 28 days ago) |
|
|
Hello all! So I'm trying to get back in the swing of things and started doing some prep stuff. While enlarging/creating my injection sites I made them rather large on accident. I was curious if anyone has worked with sites of this size before and what their outcome was. Thanks for any help you can offer.
--------------------
|
Dhearic


Registered: 01/24/14
Posts: 846
Loc: Neverland
Last seen: 1 year, 27 days
|
Re: large injection sites [Re: burgerguy]
#21581319 - 04/22/15 06:08 PM (9 years, 28 days ago) |
|
|
It won't make a difference for pf tek, you should have 4 holes evenly spaced though. Make sure your dry layer is thick enough
--------------------
Credit where credit is due.
|
Th3Issu3
Stranger Danger


Registered: 12/30/14
Posts: 671
Loc: fucktown
Last seen: 23 days, 11 hours
|
Re: large injection sites [Re: burgerguy]
#21581334 - 04/22/15 06:12 PM (9 years, 28 days ago) |
|
|
What did you use to make the hole? You should try a nail or using a drill next time...Make sure you pull off the little metal on the back side of the can. It will fall off and rust in your jars....
What do you plan on doing with the lids? Using high temp RTV? Putting in pollyfill? Just leaving them and injecting them?
I'm guessing you are going to just wrap some tin foil on that hoe and PC it then innoc half a CC in each side. It will work. Ive done it a million times. Chances of contams will go up. If you have the time and more jars and lids I'd recommend going another way. Use the search funtion and find a good lid or jar tek..
Good luck brotha
|
burgerguy
Stranger


Registered: 08/04/14
Posts: 56
Last seen: 7 years, 11 months
|
Re: large injection sites [Re: Th3Issu3]
#21581356 - 04/22/15 06:19 PM (9 years, 28 days ago) |
|
|
I used a drill. I only have one bit size and its the one to make to holes in the sgfc. I was able to time it right last time and get the holes much smaller. I didn't know I had other options other than pcing. I'll be sure to do more searches.
--------------------
|
el8tch
LHLHLHLHLHLH



Registered: 03/07/15
Posts: 464
Loc: Penn's Woods
Last seen: 8 years, 3 months
|
Re: large injection sites [Re: Th3Issu3] 1
#21581367 - 04/22/15 06:21 PM (9 years, 28 days ago) |
|
|
Quote:
Th3Issu3 said: Using high temp RTV?
You mean high-temp silicone.
|
smokestack
man on the moon


Registered: 10/27/13
Posts: 150
Loc: anywhere but here
Last seen: 1 year, 1 month
|
Re: large injection sites [Re: Dhearic]
#21581378 - 04/22/15 06:24 PM (9 years, 28 days ago) |
|
|
Quote:
Dhearic said: It won't make a difference for pf tek, you should have 4 holes evenly spaced though. Make sure your dry layer is thick enough
 You'll be fine just inject, but yeah next time use a smaller hole and use 4 of them. I have done even bigger holes than that before and it worked for me.
--------------------
If you correct your mind, the rest will fall into place. -Lao Tzu- Life is short, smile while you still have your teeth.
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 212 topic views. 13 members, 73 guests and 60 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|