|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
DMT vapor pen
#19390170 - 01/08/14 07:38 PM (10 years, 22 days ago) |
|
|
Update: Using divine tribe 2.5 ceramic donut atomizer with a variable wattage temp controlled mod (ex:vaporshark rdna40) works really well. If using dmt in powder form first prime by using short firings until melted as to avoid powder flying into your mouth.
Best results using an enail set to a low temp on a rig (no water) and carb cap
Edited by phil ozwald (08/31/16 11:32 AM)
|
420Experience
GC#3




Registered: 08/13/10
Posts: 701
Loc: Searching the Rabbit Hole...
|
|
Are you wanting to use just pure, crystalline material? You could presumably use a higher temperature than DMT's vaporization point for a solution that the DMT is dissolved in and still be okay...
-------------------- And as far as I'm concerned, it's like I say, drugs are not the problem. Other stuff is the problem. ~Jerry Garcia I am a catepillar surfing on smoke through Shpongleland...
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
yes the idea is to use pure freebase nn-DMT
|
420Experience
GC#3




Registered: 08/13/10
Posts: 701
Loc: Searching the Rabbit Hole...
|
|
You can still have pure DMT in solution... Any particular reason that you're dead set on it being the standalone crystal?
-------------------- And as far as I'm concerned, it's like I say, drugs are not the problem. Other stuff is the problem. ~Jerry Garcia I am a catepillar surfing on smoke through Shpongleland...
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
For simplicity, I would rather not have to make a solution. Also if i did make a solution would it be able to completely vaporize within one hit, I would prefer taking only one hit to break through.
|
kuntryman
Noble
Registered: 12/05/13
Posts: 92
Loc: Canada
Last seen: 10 years, 15 days
|
|
You would have to reduce the solution after you have a saturated solution. However dose will be impossible to know unless you know the purity of your material, sounds dangerous. A meth pipe is fine for vaping DMT who's going to see you? Its more trouble than its worth.
-------------------- I'm only joking maybe
|
Hashbuble
Mycocentric Mutha Fucker


Registered: 08/24/11
Posts: 860
Loc:
|
|
-------------------- The mushrooms just keep following me
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
If i were to measure out 1 mL of liquid, for example menthol e-liquid and then added 500mg of DMT, I'm guessing 3 drops of the solution would have around 50mg of DMT. I will be testing the heat of the atomizer with a thermometer to see if it can safely vape non-diluted DMT and might try the menthol DMT because the numbing qualities of menthol would be nice for holding the DMT in my lungs.
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
If the 4.5 ohm atomizer I ordered does not reach low enough to a desirable vaping temperature I have decided I will purchase a repairable atomizer and use a wiring that would have greater resistance.
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
My device came today and I have fallen in love with it. Setting it at 3.50 volts quickly vaporizes all of the DMT without burning it. I was able to break through using 25mg. I am quite satisfied
Edited by phil ozwald (01/14/14 07:49 PM)
|
snoot
look alive ∞



Registered: 01/30/05
Posts: 9,640
Loc: 45º parallel
Last seen: 18 hours, 43 minutes
|
|
too much dmt, ... dangerous!?
--------------------
∞ I am incapable of conceiving infinity, and yet I do not accept finity. - Simone de Beauvoir -
|
mndfreeze 
Shroomery Secret Service




Registered: 04/22/02
Posts: 20,529
Loc: PuppetMasterFlash
Last seen: 18 hours, 36 minutes
|
|
Quote:
phil ozwald said: My device came today and I have fallen in love with it. Setting it at 3.50 volts quickly vaporizes all of the DMT without burning it. I was able to break through using 25mg. I am quite satisfied
what device did you buy because I use an e-cig now that I quit smoking cigs and I'm really curious as to how something smiilar to it would work with DMT or another similar material.
-------------------- Nothing says love like grannies prolapsed anus! quote]Urb said: I know... Its fucked up... Ill fix it minyana..[/quote]
|
snoot
look alive ∞



Registered: 01/30/05
Posts: 9,640
Loc: 45º parallel
Last seen: 18 hours, 43 minutes
|
|
yes please go on....
--------------------
∞ I am incapable of conceiving infinity, and yet I do not accept finity. - Simone de Beauvoir -
|
encryptor


Registered: 05/15/03
Posts: 1,154
Last seen: 18 days, 19 hours
|
Re: DMT vapor pen [Re: snoot]
#19443763 - 01/19/14 05:44 PM (10 years, 11 days ago) |
|
|
V=IR hmm.. If I were using an arduino uno to power the atomizer I would choose the 3.3 volt power source. Therefore, I=V/R -> I=(3.3v/4.5ohm) -> I=.7333amp. With 5 volts I=1.111amp. From the information you gave I don't know how amperage affect temperature level reached in atomizer.
|
420Experience
GC#3




Registered: 08/13/10
Posts: 701
Loc: Searching the Rabbit Hole...
|
|
Quote:
encryptor said: V=IR hmm.. If I were using an arduino uno to power the atomizer I would choose the 3.3 volt power source. Therefore, I=V/R -> I=(3.3v/4.5ohm) -> I=.7333amp. With 5 volts I=1.111amp. From the information you gave I don't know how amperage affect temperature level reached in atomizer. 
Q is proportional to P. P is proportional to I2R. Thus, it follows that Q is proportional to I2R.
-------------------- And as far as I'm concerned, it's like I say, drugs are not the problem. Other stuff is the problem. ~Jerry Garcia I am a catepillar surfing on smoke through Shpongleland...
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
I am using the ego VV mega
|
mndfreeze 
Shroomery Secret Service




Registered: 04/22/02
Posts: 20,529
Loc: PuppetMasterFlash
Last seen: 18 hours, 36 minutes
|
|
Link.
-------------------- Nothing says love like grannies prolapsed anus! quote]Urb said: I know... Its fucked up... Ill fix it minyana..[/quote]
|
electron
Stranger
Registered: 09/25/13
Posts: 59
Last seen: 8 years, 2 months
|
|
What atomizer are you using with the vape pen? one of those glass globe ones for concentrates? Is the dmt soaking into the wick a problem?
|
Space Elf



Registered: 07/29/10
Posts: 3,371
Last seen: 7 years, 3 months
|
Re: DMT vapor pen [Re: electron]
#19487631 - 01/28/14 06:16 PM (10 years, 2 days ago) |
|
|
Quote:
electron said: What atomizer are you using with the vape pen? one of those glass globe ones for concentrates? Is the dmt soaking into the wick a problem?
I was wondering the same thing.
--------------------
|
electron
Stranger
Registered: 09/25/13
Posts: 59
Last seen: 8 years, 2 months
|
|
I've been reading all the relevant threads over at the nexus, seems like some people have had good results dissolving DMT in nicotine free e-liquid, and using a tank style atomizer. The problem mostly seems to be getting a high enough DMT concentration in the liquid for breakthrough in a reasonable number of tokes. One thread suggested dissolving it in 95℅ ethanol (191 proof everclear) which seemed to hold the most DMT per ml solvent. Seems like the atomizers meant for concentrates would work for undiluted dmt if you use a battery with adjustable voltage in order to prevent it from burning.
|
Blind fool
Herr Doktor



Registered: 10/02/12
Posts: 664
|
|
Quote:
phil ozwald said: My device came today and I have fallen in love with it. Setting it at 3.50 volts quickly vaporizes all of the DMT without burning it. I was able to break through using 25mg. I am quite satisfied
This is a really cool idea, so you dissolved the DMT and then evaporated it?
|
CosmicJoke
happy mutant


Registered: 04/05/00
Posts: 10,848
Loc: Portland, OR
|
Re: DMT vapor pen [Re: electron]
#19518602 - 02/03/14 11:07 PM (9 years, 11 months ago) |
|
|
Quote:
electron said: I've been reading all the relevant threads over at the nexus, seems like some people have had good results dissolving DMT in nicotine free e-liquid, and using a tank style atomizer. The problem mostly seems to be getting a high enough DMT concentration in the liquid for breakthrough in a reasonable number of tokes. One thread suggested dissolving it in 95℅ ethanol (191 proof everclear) which seemed to hold the most DMT per ml solvent. Seems like the atomizers meant for concentrates would work for undiluted dmt if you use a battery with adjustable voltage in order to prevent it from burning.
That's what I was wondering, I can consume 33mg of DMT in one toke with but a test tube corked with a hole drilled through it and 2 straws, one to inhale and one to fan... Strangely about 50mg takes me closer to three, I'd have to assume it's because I'm so gone after the first hit that I have no idea what I'm doing Just pushing a button on some sort of vape mod would be sweet though, would eliminate a lot of coordination issues. Getting the full dose as rapidly as possible is quite important with DMT, big refractory time in my experience, would love to vape 60mg in one hit
-------------------- Everything is better than it was the last time. I'm good. If we could look into each others hearts, and understand the unique challenges each of us faces, I think we would treat each other much more gently, with more love, patience, tolerance, and care. It takes a lot of courage to go out there and radiate your essence. I know you scared, you should ask us if we scared too. If you was there, and we just knew you cared too.
|
phil ozwald
Doctor



Registered: 08/26/13
Posts: 32
Loc: New England
Last seen: 7 years, 4 months
|
|
Update: Using divine tribe 2.5 ceramic donut atomizer with a variable wattage temp controlled mod (ex:vaporshark rdna40) works really well. If using dmt in powder form first prime by using short firings until melted as to avoid powder flying into your mouth.
Best results using an enail set to a low temp on a rig (no water) and carb cap
|
|