|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
HypnotoadCroaked
Retired, but will check MSGs

Registered: 01/05/13
Posts: 1,168
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19345766 - 12/30/13 10:38 AM (10 years, 1 month ago) |
|
|
Quote:
WillSolvem said:
Find me another way to hold a vacuum upon cooking and I'll take it into consideration.
The rocker was not replaced with a ball valve, I would point you to the Tek, but you know how self appointed policing goes 

No rocker at all? You are lucky there that you really did not blow yourself up.
Quote:
Whippy said: Quit being cheap and dangerous to yourself and others, and fork over the funds to get a cooker that will do 20psi safe. Otherwise you are a total fool.
You want a safe autoclave, buy one.
|
WillSolvem
Odd-Hand




Registered: 04/24/12
Posts: 1,519
Loc: Chapter 26
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: HypnotoadCroaked]
#19345783 - 12/30/13 10:46 AM (10 years, 1 month ago) |
|
|
Quote:
You want a safe autoclave, buy one.
I did, for $70 and $20 in fittings and a swing gauge. How much did you spend again? Hahaha
Again your just reaching, go police another thread
--------------------
AMU Q&A Thread because questions deserve answers.
|
bootster


Registered: 02/22/11 
Posts: 1,531
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19345803 - 12/30/13 10:52 AM (10 years, 1 month ago) |
|
|
As a side note, I remember when the "Short Magnum" high power rifle cartridges came out. Some manufacturers would not make barrels for them because the pressure curve was to dangerous for the materials that the barrels were made out of. The manufacturers had to rethink the makeup of the barrels to accommodate the high pressures that were dangerous to conventional chambers.
You can't reinvent the wheel. I run my sterilizer at 17 to 20 PSI when doing grains, but I don't let it become higher than 15 PSI for agar.
I liked the analogy of shooting a .22 cal long rifle cartridges and then trying to make it into a 22-250. That analogy is alarming.
For those of you who aren't familiar with rifle cartridges, the 22-250 is on the left and the 22 long rifle is on the right.

There is a deadly difference.
Edited by bootster (12/30/13 11:35 AM)
|
HypnotoadCroaked
Retired, but will check MSGs

Registered: 01/05/13
Posts: 1,168
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: bootster]
#19345831 - 12/30/13 11:03 AM (10 years, 1 month ago) |
|
|
Quote:
bootster said: I liked the analogy of shooting a .22 cal long rifle cartridges and then trying to make it into a 22-250. That analogy is alarming.
That is a great way to describe it.
I blocked Will, not because I am shamed by him, but because of his inherent lack of knowledge. I guarantee that I will learn nothing from him and his antics. I really don't want to know what he does with his pressure cooker. An autoclave and a pressure cooker are 2 different monsters with similar properties. I have not been subtle at all about what I pointed out. Just because he cannot comprehend that he did disable integrated safety mechanisms, does not mean at all that it is safe. What was done was totally unsafe. There is no other way about it. It is all wrong. All I requested is that you keep that sort of bs to yourself. There are too many impressionable minds that simply don't comprehend what they are dealing with...Will included.
I will continue to "police" threads and report ANYTHING that looks like a bomb. 30+ PSI in a cooker rated @ 15 psi is a bomb.
|
WillSolvem
Odd-Hand




Registered: 04/24/12
Posts: 1,519
Loc: Chapter 26
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: HypnotoadCroaked]
#19345859 - 12/30/13 11:15 AM (10 years, 1 month ago) |
|
|
Flaming and trolling is bad, mmmk.
Edited by Citric (12/30/13 12:16 PM)
|
WillSolvem
Odd-Hand




Registered: 04/24/12
Posts: 1,519
Loc: Chapter 26
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19345898 - 12/30/13 11:24 AM (10 years, 1 month ago) |
|
|
My first block!!
What's the saying? "Your not doing it right if someone doesn't hate"
--------------------
AMU Q&A Thread because questions deserve answers.
|
Psilicon
Really Nice Guy


Registered: 08/26/12
Posts: 7,057
Last seen: 3 years, 2 months
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19347462 - 12/30/13 05:24 PM (10 years, 1 month ago) |
|
|
Quote:
WillSolvem said: Without a gauge to read pressure even I might be reluctant to modify. Aluminum is soft though so drilling a hole and bolting a pressure gauge would be really easy, you could then add weight to the rocker weight. The rockers are steel and magnets stick pretty well or you could glue large metal washers until desired pressure is reached.
Quote:
WillSolvem said: Aluminum is soft though so drilling a hole and bolting a pressure gauge would be really easy
Quote:
WillSolvem said: Aluminum is soft
Quote:
WillSolvem said: soft
I can't think of any reason this would go wrong. What are you guys so upset about?
|
WillSolvem
Odd-Hand




Registered: 04/24/12
Posts: 1,519
Loc: Chapter 26
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: Psilicon]
#19347513 - 12/30/13 05:32 PM (10 years, 1 month ago) |
|
|
Yes compared to steel. Troll somewhere else your beating a dead horse
--------------------
AMU Q&A Thread because questions deserve answers.
|
Psilicon
Really Nice Guy


Registered: 08/26/12
Posts: 7,057
Last seen: 3 years, 2 months
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19347549 - 12/30/13 05:38 PM (10 years, 1 month ago) |
|
|
I thought it was a dead horse the first time you made a thread about this terrible idea, but it turned out to still have some life in it. Yes, I'm beating a dead horse, but since this horse is a dangerous asshole I think I'm just going to keep beating it for a while.
|
WillSolvem
Odd-Hand




Registered: 04/24/12
Posts: 1,519
Loc: Chapter 26
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19347568 - 12/30/13 05:40 PM (10 years, 1 month ago) |
|
|
Will the next moderator reading this please lock this thread. Way too much off-topic discussion are muddying the waters of the original point.
--------------------
AMU Q&A Thread because questions deserve answers.
|
Citric


Registered: 03/19/04
Posts: 4,490
|
Re: Sterilization Pressure/Temperature & Duration Table [Re: WillSolvem]
#19347569 - 12/30/13 05:40 PM (10 years, 1 month ago) |
|
|
This thread has been closed.
Reason: Duh?
|
|