|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
ghast
Stranger
Registered: 11/27/12
Posts: 6
Last seen: 9 years, 6 months
|
Hows it looking? First grow tub. *DELETED*
#18999982 - 10/19/13 02:31 PM (10 years, 4 months ago) |
|
|
Post deleted by ghastReason for deletion: .
|
Mush4Brains
LOOL HACKED!!!

Registered: 07/31/13
Posts: 4,419
Last seen: 9 years, 3 months
|
Re: Hows it looking? First grow tub. [Re: ghast]
#18999996 - 10/19/13 02:33 PM (10 years, 4 months ago) |
|
|
I mean, it looks OK I guess but you really should have followed a tub tek and gotten your holes set up with poly and everything. Put a fan in the room to help circulate more air. I also would have no way of knowing if your RH is up to spec, but I would assume not. You'll no doubt get a yield, but if you would follow a tek to the T you would get far better results.
|
aomoriakuma
Sensei


Registered: 09/09/13
Posts: 176
Last seen: 7 years, 4 months
|
Re: Hows it looking? First grow tub. [Re: ghast]
#19000001 - 10/19/13 02:34 PM (10 years, 4 months ago) |
|
|
why not just put holes in it? itll save you a LOT of trouble in the long run!
|
Stromrider
This must be the place



Registered: 06/02/13
Posts: 7,338
Loc: Dept of know what I'm say...
Last seen: 12 hours, 32 minutes
|
Re: Hows it looking? First grow tub. [Re: ghast]
#19000002 - 10/19/13 02:34 PM (10 years, 4 months ago) |
|
|
No need to mist bulk substrate before the first flush.
Monotubs perform better when properly constructed
Edited by Stromrider (10/19/13 02:34 PM)
|
ghast
Stranger
Registered: 11/27/12
Posts: 6
Last seen: 9 years, 6 months
|
Re: Hows it looking? First grow tub. *DELETED* [Re: Stromrider]
#19000018 - 10/19/13 02:37 PM (10 years, 4 months ago) |
|
|
Post deleted by ghastReason for deletion: DELETED
Edited by ghast (10/19/13 02:40 PM)
|
dirty
super sketch



Registered: 08/18/13
Posts: 120
Loc: stateside
Last seen: 9 years, 10 months
|
Re: Hows it looking? First grow tub. [Re: ghast]
#19000036 - 10/19/13 02:40 PM (10 years, 4 months ago) |
|
|
I had to use a small "new" drill bit to ensure it was sharp. I drill holes on the perimeter of my circle cutouts, used a heat gun to slightly heat the plastic then used a razor knife to basically connect the dots u could say. And make sure to have the top on the tub when you do your holes, I find it helps stabilize the co0ntainer a bit to guard against cracking. Also patience, when I make a bucket I prepare to sit awhile and do it slowly as to not ruin a good bucket.
-------------------- "In a completely sane world, madness is the only freedom" -J.G. Ballard "Why isn't there a strain yet called Rubix Cubensis?" -Fraggin
|
aomoriakuma
Sensei


Registered: 09/09/13
Posts: 176
Last seen: 7 years, 4 months
|
Re: Hows it looking? First grow tub. [Re: dirty]
#19000118 - 10/19/13 02:59 PM (10 years, 4 months ago) |
|
|
ahh i see. well it looks good considering. good luck with the grow!
|
jackalope9517
(/*o*)/


Registered: 01/16/13
Posts: 380
Last seen: 9 years, 9 months
|
Re: Hows it looking? First grow tub. [Re: aomoriakuma]
#19000125 - 10/19/13 03:02 PM (10 years, 4 months ago) |
|
|
Mine is colonized and i don't have holes in it either.. not sure how i should go about putting the holes in. I was thinking exacto knife + fire to melt the plastic a bit.
I... doubt it would work... lol. Anyone know about the can lid thing?
|
Khii Khwaay
black tooth grin

Registered: 04/16/12
Posts: 2,277
|
Re: Hows it looking? First grow tub. [Re: dirty]
#19000165 - 10/19/13 03:11 PM (10 years, 4 months ago) |
|
|
1. Heat tin can over stove
2. Push through side of tub.
It works!
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 566 topic views. 28 members, 163 guests and 22 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|