|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
jackalope9517
(/*o*)/


Registered: 01/16/13
Posts: 380
Last seen: 9 years, 8 months
|
My WBS situation. Any advice would be appreciated :)
#18787917 - 09/02/13 01:02 AM (10 years, 4 months ago) |
|
|
Hi all. So, this is going to sound pretty outrageous though hopefully not too outrageous to completely give up on.
Anyways, I recently decided to start up a WBS grow with a somewhat limited budget and i suppose i got a bit carried away cause.. by the time my jars were ready after being PCed i realized i had forgotten to do shit with the lids and look up a lid tek! Or even an inoculation tek! Doh! silly me..
Ok, so currently i have a total of 6 jars 2 being quart sized and 4 being uh.. half pint sized. Yes yes i know silly me. That's all that could fit in the PC at the time and well that's another story lol. Welp at any rate, 3 of these jars have 4 holes in the lid, through the tyvek which is underneath and on top is some loosely put foil. The other 3 jars have 1 hole in them through the underlying tyvek and also some loosely put foil on top. They're currently sitting in my closet near the ceiling.
My inoculation was retarded, my lids are retarded, and the amount of WBS I have is retarded. I am retarded.
Anywho, is there anything i can do at this point to help um out? Maybe right some wrongs? 
Think of the mushroom mycelium. The poor mycelium i am making go through this... shame on me, but pity them because they didn't deserve this. (though honestly it's been a week and the myc looks fairly decent...)
Any help would be appreciated. Thanks all.
|
Psilicon
Really Nice Guy


Registered: 08/26/12
Posts: 7,057
Last seen: 3 years, 1 month
|
Re: My WBS situation. Any advice would be appreciated :) [Re: jackalope9517]
#18787947 - 09/02/13 01:17 AM (10 years, 4 months ago) |
|
|
Sorry, but I'm not understanding the question. If your mycelium looks good, what's the problem?
|
jackalope9517
(/*o*)/


Registered: 01/16/13
Posts: 380
Last seen: 9 years, 8 months
|
Re: My WBS situation. Any advice would be appreciated :) [Re: Psilicon]
#18788018 - 09/02/13 01:50 AM (10 years, 4 months ago) |
|
|
Er well the problem is i fucked up the lids and I'm not sure what i should do about that. Or if there is anything i CAN do about it to kinda benefit it more.. ya know?
|
Pestile

Registered: 05/02/13
Posts: 875
Loc: Northern Europe
|
Re: My WBS situation. Any advice would be appreciated :) [Re: jackalope9517]
#18788185 - 09/02/13 03:27 AM (10 years, 4 months ago) |
|
|
It seems like an awful lot of extra work, but I would say either start from scratch with the correct lids or make some new lids and try to change the lids in a SAB.
The tyvek part is pretty confusing. There shouldn't be a hole in the tyvek, it must remain unpunctured and the tyvek shouldn't be underneath the lid, only under the ring. And that is for G2G. If you want to inoculate with a syringe, you'll need some kind of inoculation point which does not puncture a hole in the filter you are using.
--------------------
   The Corbett Report Open Source Intelligence News
|
jackalope9517
(/*o*)/


Registered: 01/16/13
Posts: 380
Last seen: 9 years, 8 months
|
Re: My WBS situation. Any advice would be appreciated :) [Re: Pestile]
#18789336 - 09/02/13 11:38 AM (10 years, 4 months ago) |
|
|
Quote:
Pestilence said: It seems like an awful lot of extra work, but I would say either start from scratch with the correct lids or make some new lids and try to change the lids in a SAB.
The tyvek part is pretty confusing. There shouldn't be a hole in the tyvek, it must remain unpunctured and the tyvek shouldn't be underneath the lid, only under the ring. And that is for G2G. If you want to inoculate with a syringe, you'll need some kind of inoculation point which does not puncture a hole in the filter you are using.
So if i were to just use different lids right now how should i have it? or what lid tek should i use?
|
Pestile

Registered: 05/02/13
Posts: 875
Loc: Northern Europe
|
Re: My WBS situation. Any advice would be appreciated :) [Re: jackalope9517]
#18789350 - 09/02/13 11:44 AM (10 years, 4 months ago) |
|
|
Quote:
jackalope9517 said: So if i were to just use different lids right now how should i have it? or what lid tek should i use?
I recommend these: How TL Makes His Lids (Grain, 1/4 Pint Agar & "No-Tilt" LC Lids)
--------------------
   The Corbett Report Open Source Intelligence News
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 237 topic views. 35 members, 199 guests and 25 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|