|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Running Wire to the Breaker (Electrical)
#14303368 - 04/16/11 09:05 PM (12 years, 9 months ago) |
|
|
Okay here is the scenario, I own a two bedroom condo with a spare room that I want to run a 220volt outlet to in order to supply several light fixtures, these light fixtures run at 5 amps a piece at 220volts and I would like to be able to run three of them. Now my breaker box doesn't allow me to add a new dedicated breaker because all the space is filled. What I was thinking of doing was removing the 30amp dedicated washer dryer breaker and the lines to the washer dryer and replacing the breaker with a 60 amp breaker running new 6 gauge wire rated for 60 amps to the washer and dryer and from there put a junction or whatever and run the 6 gauge romex wire back up into the attic and back down into the room where the new receptacle will be. Is this sound wiring ? The washer dryer only consume 21 amps together so adding another 15amps to this should still keep me below 75% of the 60amps. Is there something I am missing ? Any alternative suggestions? Please don't tell me to hire an electrician or that I will kill myself. I have enough sense not to get shocked/electrocuted. I some experience inside a breaker and place safety first.
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14304828 - 04/17/11 06:16 AM (12 years, 9 months ago) |
|
|
I hope you're not my neighbor.
Quote:
I some experience inside a breaker and place safety first.

It is not sound wiring and I hope you were under the influence of some type of chemical substance when you came up with this plan.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14304868 - 04/17/11 06:42 AM (12 years, 9 months ago) |
|
|
your just the type of poster i knew would respond. Your an asshole. You point out the typo I made and fail to respond with any constructive input.
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305022 - 04/17/11 08:05 AM (12 years, 9 months ago) |
|
|
Pris?
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305619 - 04/17/11 11:03 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: your just the type of poster i knew would respond. Your an asshole. You point out the typo I made and fail to respond with any constructive input.
I actually didn't notice any typo. I am however convinced you know little about breakers and wiring... and safety.
Quote:
Please don't tell me to hire an electrician or that I will kill myself.
Note that I did not.
Quote:
I have enough sense not to get shocked/electrocuted.
Now that I don't believe.
If you don't grasp the stupidity of what you wish to do, at least electrocute yourself before burning down your neighbors home as well as your own.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14305630 - 04/17/11 11:06 AM (12 years, 9 months ago) |
|
|
If I was stupid I would do it before asking. Since you have nothing to add or are unable to tell me why this is the incorrect way to go about what I want to achieve then I will assume you have little if any knowledge on the subject yourself.
I have already replaced the wiring for the stove with the approriate gauge romex during a home remodel job in which i took out the drop ceiling in the kitchen and had to run new wire. Its not to difficult to snap off the breaker take out the wiring and replace it. I know the basics of not touching hot wires etc you make it sound like you need to be an engineer or something to work on this stuff when its really comon sense. I admit to not knowing weather or not what I was to do is correct that's why Im asking in the forum. No need to be a pretentious ass.
Edited by QuantumMeltdown (04/17/11 11:11 AM)
|
puff4200
Natural born lever puller


Registered: 09/26/10
Posts: 1,269
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305646 - 04/17/11 11:11 AM (12 years, 9 months ago) |
|
|
This does sound like a bad idea...just saying. You may not believe that what i said is constructive since i didn't give you any ideas on how to do it, but it sounds like an all around bad idea to do it. Just really think about it before you get into it and i would also consider other options.
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: puff4200]
#14305655 - 04/17/11 11:14 AM (12 years, 9 months ago) |
|
|
What other options? How is it a bad idea? The breaker and wiring for the appliances will be the appropriate gauges and I will not be over loading the circuit. Does anyone with real experience care to elaborate on this ?
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305686 - 04/17/11 11:20 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: If I was stupid I would do it before asking. Since you have nothing to add or are unable to tell me why this is the incorrect way to go about what I want to achieve then I will assume you have little if any knowledge on the subject yourself.
I have already replaced the wiring for the stove with the approriate gauge romex during a home remodel job in which i took out the drop ceiling in the kitchen and had to run new wire. Its not to difficult to snap off the breaker take out the wiring and replace it. I know the basics of not touching hot wires etc you make it sound like you need to be an engineer or something to work on this stuff when its really comon sense. I admit to not knowing weather or not what I was to do is correct that's why Im asking in the forum. No need to be a pretentious ass.
This is why they have electrical codes.
Hopefully you'll harm yourself before you destroy your neighbors property.
The reason I'm not giving any advice is because your trying to do something that clearly demonstrates why you shouldn't be doing anything in an electrical box. Period.
You are a first class example of the saying... a little knowledge is a dangerous thing.
What you wish to do is dangerous, stupid, moronic and life threatening. If it was just your life involved I may have encouraged you to go ahead so I could enjoy the inevitable... "oh noze, my house burnt down!" thread.
If you don't care about your safety and your home, at least have some compassion for the home and safety of your neighbors.
Even if it was just common sense, that is something you seem to be in short supply of.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14305695 - 04/17/11 11:21 AM (12 years, 9 months ago) |
|
|
Your an idiot, get lost.
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305703 - 04/17/11 11:22 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: What other options? How is it a bad idea? The breaker and wiring for the appliances will be the appropriate gauges and I will not be over loading the circuit. Does anyone with real experience care to elaborate on this ?
No Capn' Happy, the breaker for the washer/dryer will NOT be the appropriate size. Were that so, there would have been a different breaker there to begin with,.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305711 - 04/17/11 11:24 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: Your an idiot, get lost.
Nope. The idiot is clearly the one who wants to DOUBLE the rating of the circuit breaker with no concern for his home... or more importantly, the home of his neighbor.
And for what??? So you can grow dope? You've clearly used too much already.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305714 - 04/17/11 11:25 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: Okay here is the scenario, I own a two bedroom condo with a spare room that I want to run a 220volt outlet to in order to supply several light fixtures, these light fixtures run at 5 amps a piece at 220volts and I would like to be able to run three of them. Now my breaker box doesn't allow me to add a new dedicated breaker because all the space is filled. What I was thinking of doing was removing the 30amp dedicated washer dryer breaker and the lines to the washer dryer and replacing the breaker with a 60 amp breaker running new 6 gauge wire rated for 60 amps to the washer and dryer and from there put a junction or whatever and run the 6 gauge romex wire back up into the attic and back down into the room where the new receptacle will be. Is this sound wiring ? The washer dryer only consume 21 amps together so adding another 15amps to this should still keep me below 75% of the 60amps. Is there something I am missing ? Any alternative suggestions? Please don't tell me to hire an electrician or that I will kill myself. I have enough sense not to get shocked/electrocuted. I some experience inside a breaker and place safety first.
Quoted for posterity so that when you sober up and realize just what a stupid fucking idea this is, the world will still be able to see it.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14305724 - 04/17/11 11:26 AM (12 years, 9 months ago) |
|
|
dude if your doubling the capacity of the breaker your also replacing the wires to make them able to handle that load also. I don't see how this jeopardizes anything. Did you even read my post? I can see how it could be dangerous to change the breaker out to a higher rating and not replace the wiring.
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14305738 - 04/17/11 11:28 AM (12 years, 9 months ago) |
|
|
I do not use drugs or drink you douche. Do you really have nothing better to do then argue on the internet to make yourself feel superior?
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305760 - 04/17/11 11:35 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: dude if your doubling the capacity of the breaker your also replacing the wires to make them able to handle that load also. I don't see how this jeopardizes anything. Did you even read my post? I can see how it could be dangerous to change the breaker out to a higher rating and not replace the wiring.
Because numb-nuts... the MANUFACTURER of the washer/dryer know what their equipment is rated for.
Because numb-nuts... the people that design electrical codes have a bit (huge bit) more knowledge that you do.
Hey I know... lets just run a single 500 amp circuit breaker and huge fucking cables to supply the outlets and equipment! Think of all the time and money we'df all save!
WOO-HOO!
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305769 - 04/17/11 11:37 AM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: I do not use drugs or drink you douche.
Then there is clearly another problem.
Quote:
Do you really have nothing better to do then argue on the internet to make yourself feel superior?
I'm not arguing, merely paying the proper respect to one of the stupidest fucking questions I have seen on this site.
Burn Baby... Burn!
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14305790 - 04/17/11 11:41 AM (12 years, 9 months ago) |
|
|
The appliance should only draw as much current as it needs unless it becomes defective. The breaker is to protect the wiring in the home not the appliance and so long as the wiring is the appropriate gauge for the breaker I see know reason why this will not be safe. I single light bulb does not draw 15amps yet you can run multiple lights on a 15amp circuit and there is no problem. This logic could be flawed but I you have not stated why and this is why I am asking on the forums before doing something like this because I do value my home and the safety of my neighbors. I didn't come on here to argue guy I'm just looking for answers from someone who doesn't think their too elite to provide them to an "amateur" .
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305804 - 04/17/11 11:44 AM (12 years, 9 months ago) |
|
|
Quote:
The appliance should only draw as much current as it needs unless it becomes defective.
There you go numb-nuts. You just hit upon the problem.
I knew ( ) you could do it.
Now, have pity on your neighbors, since you clearly don't give a shit about your safety.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14305836 - 04/17/11 11:51 AM (12 years, 9 months ago) |
|
|
Im getting some help from a real DIY form where the folks don't insult one another and aren't to elite to answer questions. I apologize for the names I have called you I think I am done here unless you or anyone else cares to go more in depth.
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14305931 - 04/17/11 12:09 PM (12 years, 9 months ago) |
|
|
Okay Ive got it figured out. My box accepts tandem breakers. I will replace the 30 amp washer/dryer breaker with a tandem breaker 30amp/20amp leave the wiring alone for the washer dryer and run dedicated wiring for the lighting.
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14306314 - 04/17/11 01:13 PM (12 years, 9 months ago) |
|
|
Close. I've never seen tandem 220 volt breakers (as they are double pole already). Tandem breakers are available for 110 volts circuits though.
Replace enough of your single 110 breakers to open up a spot for an additional 220 breaker.
Tandem breaker. Note there is no tie-bar between the two. This type must NOT be used for what you wish to do as one leg could trip while leaving the second leg live.
Double pole breaker. This is for use on 220 volt single phase circuits so that both legs of the circuit trip off at one time.
Also, I've never seen a tandem breaker that was rated for two different amperage's. They are (as far as I know) ONLY available in ratings such as 20/20, 15/15 and so on.
So in summation... use tandem breakers for 110, not 220.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
QuantumMeltdown
Space Monkey



Registered: 10/31/01
Posts: 4,962
Loc: Ft. Lauderdale, FL
Last seen: 5 months, 11 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14306606 - 04/17/11 02:07 PM (12 years, 9 months ago) |
|
|
Okay now were getting somewhere thank you for the helpful information really, I think what I was refering to is called a quad breaker I have one for my ac and water heater its the size of a regular 220 breaker but has two switches one 30amp for the ac and one 20 amp for the water heater. Now I could do something like that but I think I like your idea of replacing a few 115 breakers for tandem to make room for a 220. Again I apologize for the little quarel.
-------------------- -QuantumMeltdown Total abstinence is so excellent a thing that it cannot be carried to too great an extent. In my passion for it I even carry it so far as to totally abstain from total abstinence itself. -Mark Twain "The time has come the walrus said, little oysters hide their heads, my Twain of thought is loosely bound I guess its time to Mark this down, Be good and you will be lonesome Be lonesome and you will be free Live a lie and you will live to regret it That's what livin' is to me That's what livin' is to me" Jimmy Buffett
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14310860 - 04/18/11 08:21 AM (12 years, 9 months ago) |
|
|
Stay away from the quads. The action on them has always sucked. Replace 2 of the standard single pole breakers with tandems and that will leave room for the new double pole breaker for your 220 circuit.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
Psychoslut
The Mother Fucking Bear-o-dactyl

Registered: 12/10/02
Posts: 20,917
Loc: all up in ya
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14311415 - 04/18/11 11:11 AM (12 years, 9 months ago) |
|
|
Use a tandem breaker.
--------------------
[quote]KristiMidocean said: Good now thats clear.WHO FUCKING CARES. If I am fat u all keep pointing it out like its suppose to be a secret.LIke u really have nothing better to do then make fat jokes. If o know its like I do I know yall can come up with NEW AND BETTER SHIT . This shit is old and boring . I left in the first place cause this shit got boring not because of the fat jokes . Fat jokes dont bother me but seriously its old[/quote]
|
Seuss
Error: divide byzero



Registered: 04/27/01
Posts: 23,480
Loc: Caribbean
Last seen: 2 months, 21 days
|
Re: Running Wire to the Breaker (Electrical) [Re: Psychoslut]
#14316746 - 04/19/11 11:22 AM (12 years, 9 months ago) |
|
|
> Use a tandem breaker.
A 220v breaker is already a tandem breaker.
-------------------- Just another spore in the wind.
|
Psychoslut
The Mother Fucking Bear-o-dactyl

Registered: 12/10/02
Posts: 20,917
Loc: all up in ya
|
Re: Running Wire to the Breaker (Electrical) [Re: Seuss]
#14316994 - 04/19/11 12:04 PM (12 years, 9 months ago) |
|
|
my bad, thats why im only a 3rd year apprentice, and have to have journeyman backup lol.
well its that, and i have no experience in residential, only industrial. the circuit breakers i fuck with are the size of VW beetles.
--------------------
[quote]KristiMidocean said: Good now thats clear.WHO FUCKING CARES. If I am fat u all keep pointing it out like its suppose to be a secret.LIke u really have nothing better to do then make fat jokes. If o know its like I do I know yall can come up with NEW AND BETTER SHIT . This shit is old and boring . I left in the first place cause this shit got boring not because of the fat jokes . Fat jokes dont bother me but seriously its old[/quote]
Edited by Psychoslut (04/19/11 12:06 PM)
|
Prisoner#1
Even Dumber ThanAdvertized!


Registered: 01/22/03
Posts: 193,665
Loc: Pvt. Pubfag NutSuck
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14320069 - 04/19/11 09:54 PM (12 years, 9 months ago) |
|
|
Quote:
QuantumMeltdown said: Pris?
it's 'illegal' and can be dangerous, what you can do is install that 60 amp and run the wire to a sub panel with a few breakers in it to pull the load for the lights and the dryer as long as you arent exceeding the rating of the main panel...
|
Seuss
Error: divide byzero



Registered: 04/27/01
Posts: 23,480
Loc: Caribbean
Last seen: 2 months, 21 days
|
Re: Running Wire to the Breaker (Electrical) [Re: Prisoner#1]
#14321580 - 04/20/11 04:51 AM (12 years, 9 months ago) |
|
|
> as you arent exceeding the rating of the main panel...
In the picture above, why are you pulling through breakers (for the subpanel) rather than from the incoming mains?
-------------------- Just another spore in the wind.
|
Psychoslut
The Mother Fucking Bear-o-dactyl

Registered: 12/10/02
Posts: 20,917
Loc: all up in ya
|
Re: Running Wire to the Breaker (Electrical) [Re: Prisoner#1]
#14321623 - 04/20/11 05:51 AM (12 years, 9 months ago) |
|
|
Nice smurf tube job brah.
--------------------
[quote]KristiMidocean said: Good now thats clear.WHO FUCKING CARES. If I am fat u all keep pointing it out like its suppose to be a secret.LIke u really have nothing better to do then make fat jokes. If o know its like I do I know yall can come up with NEW AND BETTER SHIT . This shit is old and boring . I left in the first place cause this shit got boring not because of the fat jokes . Fat jokes dont bother me but seriously its old[/quote]
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: Seuss]
#14321674 - 04/20/11 06:32 AM (12 years, 9 months ago) |
|
|
Quote:
Seuss said: > as you arent exceeding the rating of the main panel...
In the picture above, why are you pulling through breakers (for the subpanel) rather than from the incoming mains?
I can think of two reasons.
1. He didn't have to shut off the power to the entire house to install the sub-panel. 2. Electrical code.
This (at least in my area) is a code requirement. I believe it is part of the National Electrical code as well. If the sub-panel is run directly from the mains, a person unfamiliar with that set-up may not realize the sub-panel is still live after turning off the main breaker.
Now that's OK I guess if you don't like that person, but it could come as a surprise to others.
A "shocking" surprise.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
Psychoslut
The Mother Fucking Bear-o-dactyl

Registered: 12/10/02
Posts: 20,917
Loc: all up in ya
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14321711 - 04/20/11 06:55 AM (12 years, 9 months ago) |
|
|
They shouldnt be working on it if they have no idea how to check for power before they start poking at shit with a unrated stanly.
If they fry themselves fuckem, they new they were messing up.
--------------------
[quote]KristiMidocean said: Good now thats clear.WHO FUCKING CARES. If I am fat u all keep pointing it out like its suppose to be a secret.LIke u really have nothing better to do then make fat jokes. If o know its like I do I know yall can come up with NEW AND BETTER SHIT . This shit is old and boring . I left in the first place cause this shit got boring not because of the fat jokes . Fat jokes dont bother me but seriously its old[/quote]
|
luvdemshrooms
Two inch dick..but it spins!?


Registered: 11/29/01
Posts: 34,247
Loc: Lost In Space
|
Re: Running Wire to the Breaker (Electrical) [Re: Psychoslut]
#14321873 - 04/20/11 08:06 AM (12 years, 9 months ago) |
|
|
Quote:
Psychoslut said: They shouldnt be working on it if they have no idea how to check for power before they start poking at shit with a unrated stanly.
If they fry themselves fuckem, they new they were messing up.
And people who have little to no electrical knowledge shouldn't be working in a breaker box to begin with... yet they do.
None of which changes the electrical code.
Thanks for your clever comments though.
-------------------- You cannot legislate the poor into prosperity by legislating the wealthy out of prosperity. What one person receives without working for another person must work for without receiving. The government cannot give to anybody anything that the government does not first take from somebody else. When half of the people get the idea that they do not have to work because the other half is going to take care of them and when the other half gets the idea that it does no good to work because somebody else is going to get what they work for that my dear friend is the beginning of the end of any nation. You cannot multiply wealth by dividing it. ~ Adrian Rogers
|
sandi
omg


Registered: 04/11/11
Posts: 796
Loc: M6 (Butterfly Cluster)
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14321896 - 04/20/11 08:16 AM (12 years, 9 months ago) |
|
|
When my better half gets up I can have him read your post...
--------------------
Edited by sandi (05/22/11 06:36 AM)
|
sandi
omg


Registered: 04/11/11
Posts: 796
Loc: M6 (Butterfly Cluster)
|
Re: Running Wire to the Breaker (Electrical) [Re: QuantumMeltdown]
#14322019 - 04/20/11 08:58 AM (12 years, 9 months ago) |
|
|
Well, he just read it. Granted he just got up but here is his take:
"Number one, the risk of electrocution is from the outside source when you're replacing the breaker, you somehow need to have a way to shut off the outside source of power to the breaker box (to actually be safe when doing the work) then once the 60 amp breaker is put in, of course leave it in the off position, so that the work inside the condo can be done. From the 60 amp breaker to the washer dryer "junction box", I would definitely use a higher gauge than 6 gauge to be on the safe side. Don't always go by the rating of the wire because the wire will warm up in your usage. From the "junction box" near the washer dryer to your little experiment, the 6 gauge would be okay. The other part of your plan that worries me is exactly what will your junction box me made of, ie. the box itself and how are you distributing the power from it (how are you wiring it). And last but not least, do you know for sure that the power feeding your circuit breaker box has enough capacity to allow for this extra amperage use, ie. you're not going to be blowing some breaker further up the line, and the wires coming to your breaker box are rated for the extra current."
--------------------
|
Seuss
Error: divide byzero



Registered: 04/27/01
Posts: 23,480
Loc: Caribbean
Last seen: 2 months, 21 days
|
Re: Running Wire to the Breaker (Electrical) [Re: luvdemshrooms]
#14322421 - 04/20/11 10:46 AM (12 years, 9 months ago) |
|
|
> 1. He didn't have to shut off the power to the entire house to install the sub-panel.
Good point, though I usually kill the building power when working inside a panel for safety reasons. It may be inconvenient, but I value my life and have accidentally shocked myself too many times over the years.
> 2 ... If the sub-panel is run directly from the mains, a person unfamiliar with that set-up may not realize the sub-panel is still live after turning off the main breaker.
There is no main breaker in the picture above, thus I assume the building shutoff (main breaker) is upstream somewhere.
> And last but not least, do you know for sure that the power feeding your circuit breaker box has enough capacity to allow for this extra amperage use
A good point, but if he is only adding a single 20 amp circuit, he is probably safe. Even if the panel is at the design limit, it is unlikely that every circuit in the house is at maximum capacity. Still... a valid point and it would be best to verify rather than hoping for the best. I just realized another:
3. Using a breaker limits the total current allowed into the subpanel. This could be important if you are near the current capacity of the primary panel and somebody else adds more circuits to the subpanel at a later time.
-------------------- Just another spore in the wind.
|
Prisoner#1
Even Dumber ThanAdvertized!


Registered: 01/22/03
Posts: 193,665
Loc: Pvt. Pubfag NutSuck
|
Re: Running Wire to the Breaker (Electrical) [Re: Seuss]
#14329988 - 04/21/11 08:51 PM (12 years, 9 months ago) |
|
|
Quote:
Seuss said: There is no main breaker in the picture above, thus I assume the building shutoff (main breaker) is upstream somewhere.
3 boxes total, the main shut of on that one is at the pole, it's required under the state and local building codes, the pictured box is rated for 100amps as most of the homes are, I'm about to have mine upgraded to 400amps, 200 for the house (current capacity) and 200 more for the barn since I've got everything run other than making my connections on the meter base, for that I get to pull the meter and then tell the power company I have no idea why the tag on the meter is broken
|
|