|
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
psychonautis
Chemically Enhancedॐ



Registered: 03/29/10
Posts: 11
Loc: The Deep South
Last seen: 12 years, 17 days
|
PE Mycobag Pinning on Plastic
#12577985 - 05/17/10 09:26 AM (14 years, 8 months ago) |
|
|
So this is whats going on, I have a mycobag from TMS that has a fully colonized substrate of PE. The Mycellium had started to climb the sides of the bag very rapidly. I paid no attention to this due to me not wanting to irritate the mycellium, I had figured I would wait a day or two and then introduce my bag to fruiting conditions.. Well, I was absent for 2 days and when I came back and checked my bag I had pins! There are a ton of pins and primordia fruiting off the actual mycobag where the mycellium had spread up the plastic sides. The pins and primordia are on all 4 sides of the bag it's insane. I have checked the colonized substrate out to see if I am getting any pins and primordia off of it and it seems to have a good amount producing from the substrate as well(and there is a big mutant fruiting from the side of the sub as well). Now I am concerned about the colonized substrate at this point because the primordia that has formed on the sub is growing very slowly, I have pins fruiting off the mycobag sides that sit around the same level and they are growing quick. The mutant attached to the sub is also growing quick but all the other primordia growing from the colonized sub is fruiting very slow.. I am thinking of opening the bag up and introducing a little FAE and misting regimen but I do not want to ruffle the bags sides too much due to all of the myc and pins that is growing off the sides.. What do you guys think? should I just let it run its course for this flush then just dunk it and throw it in a fruiting chamber? Or should I apply FAE? All input is much appreciated!! Oh ya and also I have noticed that a pin that was growing off the side had detatched from the plastic but is still attached to the myc and is just dangling there.. Should I let it be or get it out? Thanx!
|
MrPinkFloyd


Registered: 07/13/09
Posts: 683
Loc: United States
|
Re: PE Mycobag Pinning on Plastic [Re: psychonautis]
#12578025 - 05/17/10 09:40 AM (14 years, 8 months ago) |
|
|
oof, that's long.
Pictures!
Edit: Open the bag. The myc on the side walls isn't going to do anything worth saving. Trust.
Edited by MrPinkFloyd (05/17/10 09:41 AM)
|
psychonautis
Chemically Enhancedॐ



Registered: 03/29/10
Posts: 11
Loc: The Deep South
Last seen: 12 years, 17 days
|
Re: PE Mycobag Pinning on Plastic [Re: MrPinkFloyd]
#12578102 - 05/17/10 09:57 AM (14 years, 8 months ago) |
|
|
Quote:
MrPinkFloyd said: oof, that's long.
Pictures!
Edit: Open the bag. The myc on the side walls isn't going to do anything worth saving. Trust.
Haha sorry guys for the long post I just wanted to make sure I was clear with that situation.. I will take some this evening when to post. I took some last night but the humidity in the bag kinda makes it hard to get a good picture but when I open it I will take some detailed pics because I haven't been able to find anything close searching through posts..
|
Spongiform
Some Cow


Registered: 08/22/07
Posts: 3,994
Loc: Greener Pastures
Last seen: 9 years, 4 months
|
Re: PE Mycobag Pinning on Plastic [Re: psychonautis]
#12578688 - 05/17/10 12:37 PM (14 years, 8 months ago) |
|
|
I'd suggest taking it out of the bag, dunking it for 24 hours then fruiting in a shotgun terrarium.
Would end up looking something like these albino penis envy cakes from spawn bags and fruited in a SGFC.
-------------------- Spongiform's Plastic Tek - An Alternative to Glass
Spongi's PF Block Tek & Automated Shotgun Project.
|
psychonautis
Chemically Enhancedॐ



Registered: 03/29/10
Posts: 11
Loc: The Deep South
Last seen: 12 years, 17 days
|
Re: PE Mycobag Pinning on Plastic [Re: Spongiform]
#12582010 - 05/17/10 09:23 PM (14 years, 8 months ago) |
|
|
I tried to take pics earlier so everyone could see whats going on but every photo I've taken through the bag comes out cloudy. These pics are from 2 nights ago and you can kind of see whats going on the largest pin that you see is an inch bigger now and is almost touching the substrate.. It has slightly tore away from the mycelium in one spot where it's attached to the mycobag. Is the pin going to die now that it has a slight tear from the mycelium? or will the rest of the supporting myc be able to nourish it? I am now seeing progress on the pins coming from the sub I will keep trying to take pics and keep this thread updated.
Edited by psychonautis (05/17/10 09:28 PM)
|
psychonautis
Chemically Enhancedॐ



Registered: 03/29/10
Posts: 11
Loc: The Deep South
Last seen: 12 years, 17 days
|
Re: PE Mycobag Pinning on Plastic [Re: psychonautis]
#12586034 - 05/18/10 02:20 PM (14 years, 7 months ago) |
|
|
Update on the shroom that had some tore myc around the base of the stem it didn't effect it at all. It grew another inch last night.
|
|
|
You cannot start new topics / You cannot reply to topics HTML is disabled / BBCode is enabled
Moderator: Shroomism, george castanza, RogerRabbit, veggie, mushboy, fahtster, LogicaL Chaos, 13shrooms, hamloaf, cronicr, Stipe-n Cap, Pastywhyte, bodhisatta, Tormato, Land Trout, A.k.a 1,465 topic views. 18 members, 58 guests and 23 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] |
|